Jump to content
SAU Community

Recommended Posts

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Your car looks good with the wide guards, but you definitely need some bolt on spacers for the rear! The rear wheels are sitting waaaaay too far inside the gaurds. Buy a pair of 25 or 30 mm spacers for about $120 and it will look phat!

people what would you think of the du-luck rear wing i think its the gtr one off a r33 i have seen pics it sits low and hangs out the back ?? i like but not sure if it will go with the rest of the car

The R33 GTR Do luck rear wing is not just a wing, its part of the grp boot lid so you need to buy the whole boot lid, then you have to bond or screw the quarter pieces on so they line up with the wing, the actual blade is just a GTR blade screwed to the wing uprights on the boot lid, and is not adjustable.

Not the easiest wing to fit but one of the best looking drag wings out there IMO, here's some pics of one I fitted to a mates car..

picture035ag6.jpg

picture038mg4.jpg

picture034tj3.jpg

picture040xm0.jpg

Not sure about the GTS wing but it looks like it fits to a OE boot lid, looks a lot easier to fit.

Edited by DriftyR33
well where would i get one??

Well the only place I know of is Do Luck them selves, the one I fitted was brought second hand so you could keep an eye on ebay but there rare, Do Luck are very good at keeping people from copying there kits but I'm betting someone has.

The parts you need are "Rear Wing Stay w/ Trunk Lid" & "Trunk Side Panels"

http://www.do-luck-usa.com/products.html?auto=BCNR33

http://www.do-luck.co.uk/r33gtr.htm

Not cheap though, you could just go for the GTS rear spoiler that still looks very cool IMO

http://www.do-luck-usa.com/products.html?auto=ECR33

http://www.do-luck.co.uk/r33gts.htm

:rofl:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...