Jump to content
SAU Community

Hks Gt2535 Bb Turbocharger

BigDatto
 Share

Recommended Posts

BigDatto Proficient

BigDatto

Posted
Posted (edited)

Purchased a while ago & never used. Has been peacefully resting in a box wrapped in an oily plastic bag. Turbo unit is absolutely spanking new, as are the gaskets - many of the required fittings going with it aren't new and were sourced from a used GT2530 as per the photos.

Please read the following carefully before you post your questions, guys!

This unit will bolt onto GTS-t and GTS25t manifold and exhaust. The airflow inlet is also direct fit. You will require custom oil feed line, oil drain tube, and replacement water feed lines. Alternatively the existing water feed bundy tubes can be modified by hydraulic specialists (Pirtek, Enzed etc) for minimal cost. I can provide a wastegate actuator if you wish from an R32 GTS-t. The water feed couplings for the turbo are included as per the photos.

If you'd like to know how this turbo will perform, please locate and familiarize yourself with the "search" button located directly above and to the right of this post. >_< typical results are 240-250rwKw with supporting mods, with a broad spread of torque and usable power, whilst retaining good response on an RB25 - yes it would be less linear on RB20, with a fierce rush of boost.

Price is $1500, located in Sydney. Post here or PM please.

*edit* the copper crush washers are new & unused.

post-1946-1186134338_thumb.jpg

post-1946-1186134361_thumb.jpg

post-1946-1186134380_thumb.jpg

post-1946-1186134402_thumb.jpg

post-1946-1186134421_thumb.jpg

post-1946-1186134441_thumb.jpg

post-1946-1186134463_thumb.jpg

post-1946-1186134481_thumb.jpg

Edited by BigDatto
Link to comment
https://www.sau.com.au/forums/topic/179304-hks-gt2535-bb-turbocharger/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Murray_Calavera
      WTAC 2025

      By Murray_Calavera · Posted

      Yeah mate, never miss it.
×
×
  • Create New...