Jump to content
SAU Community

Recommended Posts

hey,

well i was going to buy some whiteline sway bars but the thread started on here wont get back to me so im going into autobahn tomoro to buy some. I was just wondering what size is best for drift... ive been told thick front good and slightly skiny rear and good traction.... but if i want to set up car for drift is fat rear good??

ANyone recommend some thicknesses for r32 gtst 4 door for front and rear whiteline sway bars.

thanks

Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/
Share on other sites

actualy autobahn are $20 more expensive each than SK but i need these urgently.. Im going in today to sort things out with them. I know a few guys who work there so i get it fairy cheap. I dont know about saving $60?? I know commodores are cheaper to buy for than skylines so maybe u have a diff make of car... i dont know... maybe you got lucky.... but me mate told me he cant do them for $189 cause thats prettymuch what they pay after they have it delivered to thre store.

Anyways... i think i might get the fattest ones i can.. thanks guys

Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/#findComment-3272734
Share on other sites

If the autobarn guys can't guarantee that the bars will have minimum 3 hole adjustment (they usually have 2 hole these days) then get 24mm front, 24mm rear. It will be the only way you can balance the car.

If they are only 2 hole then you will need to set the front on hard and the rear on soft and that should be fairly balanced. If you want the thing more taily then put them both on hard.

If you go bigger on the front without the 3 hole (minimum) adjustment either end then you will not be able to dial out the understeer.

Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/#findComment-3273676
Share on other sites

Swaybars are the single best enhancement you can do for the handling of your car. They essentially link the sides of your suspension and minimize the body roll, which means your car handle much better through corners.

Make sure you buy adjustable swap bars. Adjustable bars allow you to tune in or out understeer/oversteer as required. The incremental cost of adjustable bars over non-adjustable is minimal for what you get in return.

Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/#findComment-3280935
Share on other sites

For skylines, 24mm front and 22mm rear seem to work best with normalish spring rates for street use.. Swaybars work well because they simply have the least downsides for controlling roll compared to the other methods like springs (lose compliance) and low speed bump (lose midcorner grip).

Edited by salad
Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/#findComment-3281488
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...