Jump to content
SAU Community

New Fuel Pump

COATZI

By COATZI,
in General Maintenance

 Share

Recommended Posts

COATZI Explorer

COATZI

Posted
Posted

Hi,

My fuel pump on my 96 R33 Sh!t itself, what would be some good options for an easy change over, just get a new stock one back in. Or can I put a GTR or something after market in without to much mucking around.

What kind of benefits would i have putting in something after market?

Cheers,

Link to comment
https://www.sau.com.au/forums/topic/179780-new-fuel-pump/
Share on other sites
abu Grand Master

abu

Posted
Posted

No point going back to standard, upgrade while you can.

I just upgraded from a standard pump to a GTR pump, works minttt.

Go a GTR if you don't want to spend big, it will support whatever you want to do most likely.. or if you really want to go to a new pump go a WALBRO or a BOSCH 040.

Good value for money, and will support big power.

Thanks,

Abu

Link to comment
https://www.sau.com.au/forums/topic/179780-new-fuel-pump/#findComment-3272694
Share on other sites
Habler Rising Star

Habler

Posted
Posted

I put a bosch 040 in my 33...worked a treat so far. And preety much silent! (it will be loud if you dont install it properly) You dont have to tweak anything managment wise :) But you will have to slightly mod your bracket and cut a bit off the fuel line that connects to the pump but thats easy to do. There are step by step tutes on this website to guide you through it easy!

A new pump is a better idea than a used 10 year old GTR pump. Worth the extra cash IMO

Link to comment
https://www.sau.com.au/forums/topic/179780-new-fuel-pump/#findComment-3275745
Share on other sites
tek_01 Proficient

tek_01

Posted
Posted

+1 for new pump, dont want it to fail on you again

i put a gtr one in and it was very loud (party because of the bodgy workshop that installed it wrong)

changed it for a walbro 500hp kit and it was much quieter and pretty much a straight swap, all hoses + clamps come with the kit i think the only thuing i had to change was the connectors for the positive and negative.

the 040 bosch is probably equivalent to the walbro one, either way they should both do for approx 250rwkw

Link to comment
https://www.sau.com.au/forums/topic/179780-new-fuel-pump/#findComment-3276696
Share on other sites
  • 2 weeks later...
RCHOO Grand Master

RCHOO

Posted
Posted
+1 for new pump, dont want it to fail on you again

i put a gtr one in and it was very loud (party because of the bodgy workshop that installed it wrong)

changed it for a walbro 500hp kit and it was much quieter and pretty much a straight swap, all hoses + clamps come with the kit i think the only thuing i had to change was the connectors for the positive and negative.

the 040 bosch is probably equivalent to the walbro one, either way they should both do for approx 250rwkw

I just now changed my stock pump to a Walbro..550 hp ..255 lph

Cost me 180 at Autobarn there on special till fathers day.. ;)

Link to comment
https://www.sau.com.au/forums/topic/179780-new-fuel-pump/#findComment-3300440
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...