Jump to content
SAU Community

Recommended Posts

cefiro drivers side front door $250

cefiro front standard front bar $40

cefiro bonet $170

cefiro boot $160

cefiro seats $200

cefiro door trims $120

cefiro radiator support $250

cefiro headlights pasenger side 2 of $150 each

located in brisbane

have more shit just ask

contact me on 0431535781 or pm me

Edited by drftnfrysi
Link to comment
https://www.sau.com.au/forums/topic/179926-cefiro-parts/
Share on other sites

  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

do you have the standard ceffy crossover pipe, the one without the BOV?

yes i stil have this pipe $50

i got the engine loom if u pull it out $100

door trims are black

i got the standard front and dump pipe $50

rear window $200+post and u sort out ur own post

Link to comment
https://www.sau.com.au/forums/topic/179926-cefiro-parts/#findComment-3305937
Share on other sites

Hey dude chasing sunvisors and the std front indicators the ones in the bumper???

also after some interior pieces ie stereo surround, left hand air vent surround, climate control surround??? let me know what u got my pig needs some dressing up

price to perth 6061

cheers dude

froggah

Edited by FROGGAH
Link to comment
https://www.sau.com.au/forums/topic/179926-cefiro-parts/#findComment-3316751
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...