Jump to content
SAU Community

Correct boost or not?

YBSLO4

By YBSLO4,
in Engines & Forced Induction

 Share

Recommended Posts

YBSLO4 Proficient

YBSLO4

Posted
Posted

A while back now i fitted an Autometer boost gauge, one of the better models i could get. But not long after i fitted a boost controller to level out boost and to increase boost response, but when trialling the boost controller to see if it was all hooked up i turned the boost up, but notice that once ya turn the boost controller up the maximum the boost gauge would go to on both the stock gauge and the new gauge was about 8-9psi, if you turned the boost controller up further the gauges didn't read any higher... but ya can hear from the wastegate noise that it was making more boost but it was jsut bleeding with the wastegate and not actually getting more boost to the engine. I have heard from a few guys having a similar thing happen to them in that they can't seem to get more boost than that around 8-9 at the manifold... is there something that needs to be removed for you to be able to turn the boost up to around the 13-15psi mard... maybe do ya have to bypass a factory uni tthat stops you from boosting? Or is it because its only bleed valve and i need an electronic one to boost more? I need to work it out as once the new turbo goes in and stuff i am looking to turn the boost up and it aint looking like it will happen till i work it out. Thnx peoples. J.

Link to comment
https://www.sau.com.au/forums/topic/18087-correct-boost-or-not/
Share on other sites
YBSLO4 Proficient

YBSLO4

Posted
  • Author
Posted

I installed it all, but my mate has the same boost controller its just the gated single stage controller with in cabin switch, and i copied his exactly, i knew how to do it anyway but i jsut copied his and it his works fine however mine wont...? Not sure what the deal is, and he even watched his being fitted so when it came to mine we did it exactly the same so i dunno what it is. Like i fitted some for mates aswell and mine seems to be the only one that is odd? COuld it be a faulty unit?

  • 2 weeks later...
YBSLO4 Proficient

YBSLO4

Posted
  • Author
Posted

"that y i use a DEFI for boost guage and HKS for controler...rather then Autometer and turbosmart....."

I take that your bagging my sh1t... sorry for not wasting my money on brands... Makes it easier when ya just buy a new turbo with a controlled boost wastegate actuator... don't need a boost controller. :)

skylineakt Rising Star

skylineakt

Posted
Posted

Hey YBSLO4

I saw in your mods that your turbo is from ATP. I read last time that ATP have there own combination of housings and trims. They seem really know what they are doing and they offer different stages of turbo, they also do high flow to the standard turbo yeah??

Just want to ask about your T3/4, how is it? and what kws rating is are you getting? Was it expensive??

I have seen their white R33 around but haven't seen it being pushed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...