Jump to content
SAU Community

Recommended Posts

hey all,

im not sure that something has blown but it doesnt seem to work anymore, i was wondering if there is way to tell if the amp or the speakers are stuffed..im currently running an amp for my 2 front speakers, and they used to be loud but recently don't seem to be making much noise anymore..i mainly want to know which one is stuffed so that i can replace it.

thanks heaps in advance.

Link to comment
https://www.sau.com.au/forums/topic/181048-need-help/
Share on other sites

At a guess, i'd imagine that a dead speaker would just stop working completely, and your amp shouldn't much care about the working speaker. It should remain at full volume. Have you checked your gains on the amp? Failing that, check the F/R fader controls on your headunit. If you fade to the rear, most HU's that i've used will fade to the RCA's also. So if you faded to the front, and you only had one set of RCA outputs to the amp, it would fade the front away (because the front is actually running off the RCAs, which are treated as a "rear" output generally)

Link to comment
https://www.sau.com.au/forums/topic/181048-need-help/#findComment-3290732
Share on other sites

Check all associated fuses dude...

Failing anything wrong there, you may have to take your door trims off, drop your speakers out and see if theres movement in the speakers themselves while theres some music playing.

If theres no movement, check all your wiring is still intact with a continuity test on a multimeter and/or take the speaker out and run it up on a different source (lounge room stereo etc [dont overcrank it])

Just use a process of elimination until you find where the problem lies...

Link to comment
https://www.sau.com.au/forums/topic/181048-need-help/#findComment-3294797
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
×
×
  • Create New...