Jump to content
SAU Community

trust td06-20

rob77

By rob77,
in Engines & Forced Induction

 Share

Recommended Posts

Bloodline Newbie

Bloodline

Posted
Posted

There are many different incarnations of the TD06 20G. There is a TD06-20G, TD06H-20G, TD06N-20G, TD06S-20G, TD06L-20G and TD06L2-20G. Then there are the optional turbine housing sizes as well. There are 8cm, 10cm, and 17cm housings available for the 20G based compressors. So there are 6 different turbine wheel options to mate to the 20G compressor plus the 3 housing options. There are also compressor housing options but the 20G wheel performs about the same in all of them, even the little TD05 based housing.

There are also different versions of the 25G (T67) although not as many. TD06H-25G, TD07-25G and TD07S-25G. I think there is one more but I'm not sure of the name. Turbine housing options for the 25G are as follows. 8cm, 10cm, 17cm and 22cm. So 3 or 4 turbine wheel choices and 4 housing choices. The 25G is available with a 4 inch inlet or 3 inch inlet on hte cover.

Some of these may not apply to your application but maybe helpful for the archives or just in general.

jeff

rob77 Veteran

rob77

Posted
  • Author
Posted

Ok... here's some pics and some more info. its a TD06H-20G. On the compressor wheel its got the trust part number: 49179-52010 which is different to the part number on the trust blue plate (49179-01190) It also has 0/8 and H9 written on it. The exhaust housing has a Q then DUCM then 2 then 6G also 7 9-14400. Dunno if this means anything... any more idea's of HP and spoolup time?

Bloodline Newbie

Bloodline

Posted
Posted
Originally posted by sidewaymambo

Bloodline..my TD06-25G (T67) has 16cm turbine housing ..

Ahh.. another choice that I wasnt even aware of. Thanks for pointing that out.

Now on to the turbo itself. I cant say with any certainty at what rpm the turbo will spool on your application as I am not familiar with the performance of that turbine housing. I will say that the TD06H-20G in an 8cm turbine housing is capable of 450+whp at its limit on a 2.0L engine. I have made right at 400whp on the smaller TD05H-20G 7cm on a 2.0L. The 20G compressor is rated at approximately 44lbs/min depending on who you ask.

Now to the turbine wheel. The TD06H turbine mated to a larger compressor can deal with power levels nearing 550whp. I have seen a 2.0 dyno 611whp on a 75 shot using a TD06H turbine wheel in a 7cm housing.

I know that this is not a direct answer to your question, but hopefully it will provide some insight to what you can expect out of the turbo.

jeff

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      Hi, i’m making Vag coil loom for rb25det, can anyone confirm the wire guage i’m using for power supply in diagram is enough for supply not too small for loom? For earth do i need to follow the same procedure or i can use only 16awg wire for all coil and their connecting wire following to the plug?
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
×
×
  • Create New...