Jump to content
SAU Community

Recommended Posts

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

Pre payment just completed for 2 ppl: 2x$35

Paul you should have received my sms with the details.

Ray

sorry for the late reply we just got back from autosalon what a mission

we have received the payment thanks

Woohoo!

i came 3rd place with 223rwkw --> $150 A&B Voucher :)

(ran in 4th gear, bonnet down, temp sensor in correct position AT & IT was only 2degrees difference.)

Well organised, friendly bunch of people who know what they were doing.

Cost: $35(pre-paid)

-Dyno Run plus 2 prints out 1. Power vs Air/fuel ratio 2. Power vs Boost

-Unlimited FOOD +DRINKS (BBQ+BEER!!)

-Prizes!!

what more can you ask for from a dyno day ??

Will definately be going to the next one in the future (i think they are holding one just before xmas)

First Place: i believe was this custom converted convertible Datsun 260z made 380rwkw!!

2nd Place: 180sx/s13 making 228rwkw.

Woohoo!

i came 3rd place with 223rwkw --> $150 A&B Voucher :thumbsup:

(ran in 4th gear, bonnet down, temp sensor in correct position AT & IT was only 2degrees difference.)

Well organised, friendly bunch of people who know what they were doing.

Cost: $35(pre-paid)

-Dyno Run plus 2 prints out 1. Power vs Air/fuel ratio 2. Power vs Boost

-Unlimited FOOD +DRINKS (BBQ+BEER!!)

-Prizes!!

what more can you ask for from a dyno day ??

Will definately be going to the next one in the future (i think they are holding one just before xmas)

First Place: i believe was this custom converted convertible Datsun 260z made 380rwkw!!

2nd Place: 180sx/s13 making 228rwkw.

Congrats Ray! :)

I was there, 2nd car to be put on the dyno. I got 145.5kWs with my car. Not much in comparison to the top 3, but considering I was expecting 130-140 I was very happy :).

Would of stuck around but I had a party to attend, and my dyno sheet to show off :rofl:




  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...