Jump to content
SAU Community

Recommended Posts

Ok as mentioned in the topic i want to get some coilovers soon but there is a problem..there is so much choice for the amount of money i am looking at spending.

I have a budget of say up to 1400 maaxx prefer a little less but of course will pay a bit more if there is a point. So i have looked at d2, BC, g4? second hand cusco (i had cusco adj coils in my other r33 and they where stiff as hell) the g4s where lik 1399$ which was teh most and the bcs and d2s where around 1000$

so what why should i go? are there any others out there that suit my budget. Car is a 96 gtst.

Cheers!!

Link to comment
https://www.sau.com.au/forums/topic/183453-looking-for-new-coilovers-soon/
Share on other sites

if you're looking for quality AND value for money, you could consider the HSD coilovers priced from $1330. HSD coilovers were used on Darren Appletons winning car in the 2005 Drift Australia series.

for prices click here:

http://www.amecautocare.com.au/HSD.htm

cheers

i think you need to be more specific man... ie.. are you using the car on the track/street/drag/ etc. are you after comfort/ultra low... height/dampening. etc. i'd save up a bit more dosh and go for the aus spec teins. there a great all round coilover, comfort, but still handle. you can get em from fulcrum anywhere., probably other places too. i've driven a car with hsd's, there good cheap suspension too.

I'm getting some Tein SS from Nengun in the next couple of months. They offer a really good price and the Tein SS are perfect for street driving. Do a lot of research and match the suspension to your application.

I've currently got d2 in my r33, they are bumpy but for the price i pay they are a good entry level coilover (i have the track spec ones)

I have done drift practices, mc days and a few other sprint days; and found the car to handle pretty good. Im about to upgrade to Tein Circuit Master Type RS, as im looking to get more hardcore about my track time

I think you will find most china spec entry level coilovers will be pretty similar if not the same (they are all pretty much made in the same factory). Most people comment on how bumpy and hard the ride is for j-spec coilovers (hks,tein, trust etc etc) but i think it something you just get uses too and if the coilover is of good quality the damper adjustment should help to reduce the hardness of the ride

  • 3 weeks later...

D2 and G4 are essentially the same units just rebadged and different colours. They are cheaper entry level units and the spring rates are a bit on the hard side for the road. I've stuck with my d2's now for a while but I have down rated my spring rates and they are better now. If you could afford it I would go witth Tein ss or the whiteline kits.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...