Jump to content
SAU Community

Recommended Posts

cheers for all the input fallas, i hope none of you ever have to go through that and at the same token i wish i didnt get out of my car and just grabbed the rego and gave it to the cops then maybe i would have some compensation for the dent in my car. but then again my word against five of theirs......

nah im happy i did what i did and its about time people started to respect other people and their cars. i seriously wouldnt even damage my worst enemies car just on the simple fact that its a low blow like a kick to the balls.

I think it was just a really bad case of jealousy, hopefully it will deter these idiots from doing this kinda shit again.

The look on their faces was priceless, i dont think they ever imagined any thing of the sort would happen in the middle of the road at a set of traffic lights.

*Pulls out notepad*

Note to self: Do NOT kick loymclure in the balls or throw things at his car... high probability of a punch to the face :closedeyes:

Also that sucks about what they did to your car to many people have no respect for other peoples possessions.

then his mate proceed to throw a bottle at my car and left a dent in the sill just below my roof rack.

Id be feeling mighty stabby at that point. Makes ya wanna be a no clearance bogan with a long list of priors, just enough time to "shnnaap em"

Yeah that would be my car , i work for CE in dispatch

I did not know that! I'm in the call centre (sorry 'contact centre') look up Graham Jones in the phonebook. I swear i don't look that stoned in real life. Say hi if you see me.

Edited by p1r4t8r
  • 3 months later...
Only thing i got off the rego was NSW BBQ but the Q could of been a D or an O and the car was definately a mazda 3 black/charcoal so im guessing QBN or Jerra

dont think it was ballsy at all any one cowardly enough to throw something out a car at Traffic lights with 4 of thier mates in the car would have to be a coward, When i got out of my seat first up i yelled "GET THE F*CK OUTTA THE CAR" no doubt in my mind i would of finnished off all 5 of em . Just couldnt get the dogs door open.

I know this was ages ago but saw a car and reminded me of this thread...strangely enough

A black mazda 3, green p plates, NSW rego BBD-95F driving through tuggers

  • 6 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...