Jump to content
SAU Community

2008 Mazda 6 Revealed

Forged

By Forged,
in General Automotive Discussion

 Share

Recommended Posts

Forged Experienced

Forged

Posted
Posted

Mazda_6_Frankfurt_005.jpg

Mazda_6_Frankfurt_100.jpg

Mazda_6_Frankfurt_003.jpg

The new Mazda6 has been revealed in all its glory ahead of its unveiling at next week’s Frankfurt Motor Show. The new model, once again available in sedan, five-door hatch and wagon bodystyles, brings a new sense of style and design that we predict will lure away customers of more expensive makes. The pictures reveal a dynamically styled model that make rivals like the Toyota Camry and Subaru Legacy look like design school rejects.

Mechanically, the new Mazda6 shares much in common with Ford’s Mondeo range but its dimensions are smaller and its kerb weight will likely be less as well. Officials have revealed that one of the key goals in designing the new Mazda6 was to keep weight low. Not surprisingly, the car weighs less than the outgoing version but also offers more interior space and performance. Less weight also leads to correspondingly lower fuel-consumption figures and less carbon-dioxide emissions than the current too.

Some of the new features of the Mazda6 include xenon headlights, LED detailing, active cruise control and parking sensors. Inside, there’s dual-zone climate control, an engine starter button, heated seats, voice-activated controls and a Bose stereo system. Though we suspect many of these features will be only available as an option, it’s still impressive to see a carmaker offering such lavish features in one of its mainstream models. We’ll post up a story with all the official goodies once the car makes it debut in Frankfurt but until then enjoy all the stunning pics.

www.autoblog.com

Link to comment
https://www.sau.com.au/forums/topic/184218-2008-mazda-6-revealed/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Rezz
      Duncan's V37.......race car?

      By Rezz · Posted

      Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Turbodoc
      Noobie Stagea owner..

      By Turbodoc · Posted

      Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      See if you can thermal epoxy a heatsink or two onto it?
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
×
×
  • Create New...