Jump to content
SAU Community

R33 Series 1 Wreck

EastCoastCustoms
 Share

Recommended Posts

EastCoastCustoms Enthusiast

EastCoastCustoms

Posted
Posted

hey guys

have a full r33 seresi 1 wreck here in black - has had a front end smack

everything minus engine and gearbox

will list some of the shit but it is a full wreck so any bit you want just let me know

- drivers and apssenger doors with windows and regulator

- mirrors

- 2 door boot lid with spoiler

- manual gear boot, surround, console

- r33 dash cluster and surround (90 ***kms)

- 2 door r33 rear tail lights in black

- drivers side windows witch

- VGC driver and passenger front seats

- digital climate control

- all seat belts

- r33 combination switch

- all interior trims

- m spec side skrits

- roof lining / interior lights / sun visors

- rear seats

- complete rear cradle

- rear bar rio bar

- diff

- drifeshafts

- rear struts

- front and rear brake calipers and lines

too much too list

just message or PM with offers on any gear you may want

or call 07 3862 8009 or email to [email protected]

all items locate din qld

will post items at buyers expense

Link to comment
https://www.sau.com.au/forums/topic/184744-r33-series-1-wreck/
Share on other sites
EastCoastCustoms Enthusiast

EastCoastCustoms

Posted
  • Author
Posted (edited)

it is a whole wreck and i dont know what parts people may want or not

will not post a price for every single little piece from a wreck as there is literally thousands

if you are interested in something, please PM or email

for the common shit::

front calipers $275

front rotors $150

full rear cradle $450

- rear calipers and rotors $300

- diff $250

r33 front seats (fit into s13's very well with slight modification of one bolt hole) $500

booster $50 (read above psot)

rear hubs $220

handbrake ratchet $150

handbrake cable $100

manual tailshaft $250

clutch pedal box $200

manual surround console + gear boot $100

Edited by EastCoastCustoms
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...