Jump to content
SAU Community

Recommended Posts

Good son of rajab theres been some corkers this weekend.

Its like making a cordial drink man. The aim is to make MORE drink, but at the same have the same strength taste. Uv got the ability with your big turbo to pour (move more air) more water into the glass, but where as a weak (lean) drink will just agitate you.. a lean mixture will uncontrollably ignite in your engine and pop it.

FPR (and pressure raise) + SAFC will allow some leeway... but really, if you KNOW you want power, and have a bigger tahbin in mind, grab a real aftermarket ECU and some injectors, sell the FPR and tune to your next bottleneck.

Its not just about a free flowing water source, u gota be able to accurately meter your cordial concentrate delivery, otherwise its weak city and boom.

Good son of rajab theres been some corkers this weekend.

Its like making a cordial drink man. The aim is to make MORE drink, but at the same have the same strength taste. Uv got the ability with your big turbo to pour (move more air) more water into the glass, but where as a weak (lean) drink will just agitate you.. a lean mixture will uncontrollably ignite in your engine and pop it.

FPR (and pressure raise) + SAFC will allow some leeway... but really, if you KNOW you want power, and have a bigger tahbin in mind, grab a real aftermarket ECU and some injectors, sell the FPR and tune to your next bottleneck.

Its not just about a free flowing water source, u gota be able to accurately meter your cordial concentrate delivery, otherwise its weak city and boom.

That my friend, is a GREAT analogy. very good

could've used scotch, but cordial's more PG I guess. No one likes watered down scotch.

Although there is a catch, if the wastegate in your turbo is set to a very low boost at standard then running it with no aftermarket ECU should be safe, it won't be the best, but it'll be safe. I mean, if you had a TD06 25G, and the wastegate was set to 8 PSI (hypothetically speaking of course) then its no different to a standard sized turbo with a wastegate set to 8 PSI, as after it reaches this amount of pressure both turbos will bypass. In fact being a bigger turbo you might find that at lower RPM's the turbo dosen't spool up fast enough to push as much air, and thereby gives you a RICHER mixture. However this is only if your bigger turbo runs an internal wastegate that's set to a close to stock pressure... most aftermarket turbos aren't.

Bottom line, your fuel needs to match the air going in, running rich or lean is not optimal... but too lean can be dangerous.

could've used scotch, but cordial's more PG I guess. No one likes watered down scotch.

Although there is a catch, if the wastegate in your turbo is set to a very low boost at standard then running it with no aftermarket ECU should be safe, it won't be the best, but it'll be safe. I mean, if you had a TD06 25G, and the wastegate was set to 8 PSI (hypothetically speaking of course) then its no different to a standard sized turbo with a wastegate set to 8 PSI, as after it reaches this amount of pressure both turbos will bypass. In fact being a bigger turbo you might find that at lower RPM's the turbo dosen't spool up fast enough to push as much air, and thereby gives you a RICHER mixture. However this is only if your bigger turbo runs an internal wastegate that's set to a close to stock pressure... most aftermarket turbos aren't.

Bottom line, your fuel needs to match the air going in, running rich or lean is not optimal... but too lean can be dangerous.

No entirely accurate.. a bigger turbo at standard boost will still flow more air then a smaller turbo at the same boost. Also the maps will be completely incorrect for the turbo flow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...