Jump to content
SAU Community

Recommended Posts

post-30664-1191302629_thumb.jpgpost-30664-1191302709_thumb.jpg

post-30664-1191302832_thumb.jpg

For Sale:

Skyline R32 GTS, 1992 model, 5 speed manual

Engine conversion engineered to an RB26 twin turbo with R33 GTS-T gear box

Gunmetal grey, 18 inch Traffic Star Rims

Engine only done 7000kms, car done 180 000kms (new forge pistons and rings), bored and honed, head service (fully ported and polished)

New exedy clutch

GTR brakes & hub upgrade

Limited Slip diff

3 inch exhaust and hi-flow cat

Runs 12s with amatuer driver on soft tune

245kw at the wheels

$17 000 neg.

Contact:

Erin

Edited by em_janeR32
  • 1 month later...
  • 1 month later...

Any problems with the car?

Has it been in any accidents in the past?

What is the reason for sale?

Any modification done to the engine?

When the engine was rebuilt have you put new turbos on or have the old ones been rebuilt?

Any modifications done (excluding previously stated exhaust/cats) to the car or is the engine totally stock?

Any cosmetic scratches or dents on the car?

Can you post more pictures of the car especially the interior with the seat covers removed?

Would you sell for a lower than 15k with stock wheels?

Edited by UNTS-1

There are no problems with the car.....I have alwayz used it as an everyday car and therefore had to ensure it was in good condition for daily use.

In the 2 and a half years I have owned it there was one accident where I was nudged from the back before all of the modifications began, which managed to hit only my exhuast and pushed it up.....the whole exhaust system has been upgraded and replaced to suit the rb26.

I'm selling due to buying a house.

It still has the original turbos on it, they were still in good nic

Engine is stock except for performance maintenance like porting, polishing, honing etc.

Being an older car there are scratches but still remains in good condition

I havent got any other pics of the interior atm. there is only 1 small rip on the drivers side seat.

I'd like to keep the wheels on it as I have no use for them when the car is sold.

Any other questions just let me know.

Thanks

Erin

Where was the conversion done?

Do you have receipts for head work etc?

The conversion was done at home with my ex-bf who works for Croydon Racing Developments who can vouch for all the work done by himself and my father (who built drag cars). I don't have receipts for head work.

  • 2 weeks later...
i got 16.5 for my 300+ ATWKW GTR, why is yours worth 14?

I will give you 8.5 cash. Tomorrow.

I'm going off current market value...including those advertised on here with most GTRs being sold for around 16K for basics or more and considering u were sellin it for 18K to start off with says sumtin. I believe it is well worth the money and good luck finding a similar find any cheaper. 8.5 cash u have got 2 b jokin.

Edited by em_janeR32
I started at 25 for the gtr, it was up for sale for 8 months.

But any who good luck with the sale it is definatly a tidy 32.

Thank you.....I have looked after it well

Edited by em_janeR32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...