Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm selling my RB26 head. It was on my friends car in japan. It was removed as he fitted a brand new nissan crate motor so he got the head whipped off the old donk and sent it to me. It was inspected at prime garage before being sent and it is in fine condition. I'm asking $1000 for it. What you get for that:

RB26 head ready to bolt on to the block of your choice. it's complete with:

rocker covers

timing belt cover

cams

cam gears

valves

valve springs

retainers

lifters etc.

basically, head, covers, full valve train. no ancillaries, no coil packs etc. I will take some pics tomorrow, but it's nicely gift-wrapped in plastic and I don't want to open it up but I'll do my best. This would be perfect for someone building a 30DET. get 30 bottom end. slap on this head. bolt on a turbo kit, plenum etc and bob's your uncle.

Pics: I'm not willing to unwrap it for better pics as it's nicely wrapped right now. Customs cut a few holes to peak in but that's it.

picture001yf2.jpg

picture002id4.jpg

picture003nt9.jpg

picture004rq9.jpg

picture007ps9.jpg

picture009cj4.jpg

Link to comment
https://www.sau.com.au/forums/topic/188069-rb26-complete-head-fs-sydney/
Share on other sites

yes it's cheap considering it's pretty much a bolt on jobbie for whatever block you have.

no throttle bodies mate. basically nothing attached to the head except for what's listed about. my advice would be either pick-up some GTR intake gear which is not too bad around $400 or so by the time you get it all. Lucky lots of big HP GTRs run aftermarket plenums and single throttles so it's not too hard to find.

no worries. I may be able to help organise some freight to melbourne, but either way it will have to be picked up from here.

it's sold seperately as the whole engine wouldn't fit into the boot of the car I was importing! and the bottom end had worn bearings, so it wouldn't have been much good. so I asked them to check head, remove the head and let them keep the bottom end as an early christmas present.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
    • Probably. I take it that they are also mentioned to be for R34 Skyline? For example.... RDA has that part as RDA7957. I have the dimpled and slotted version of that on my car https://www.ebay.com.au/itm/285518478694?srsltid=AfmBOopKxMuAFpsxZJdB1cam4D5RAj1f9yJyOttPZLAwXVNCOiwlhrIy This is DBA's top one piece equivalent https://www.ebay.com.au/itm/364246686631?srsltid=AfmBOorbb0XHQgqTvZLgQPhg70nqJtGvdojKnugum3O2LFSr2h-obp8D  
    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
×
×
  • Create New...