Jump to content
SAU Community

Recommended Posts

I've got my turbotech boost controller set to 10psi, and it worked great for about a week. Now when accelerating past 4,500rpm boost drops noticeably to about 5psi (although the gauge shows 5psi it doesn't even feel like it's making that much boost). It's a really noticeable drop off in power.

I took it to the mechanics the other week and wouldn't you know it, the car worked fine when I was there.. but the problem is back now. Any suggestions of where to look? Will it just be a leak in the vacuum line?

Problems driving me nuts.. boost seems to work and pull fine prior to hitting those higher revs, like the additional pressure is causing a leak???

Link to comment
https://www.sau.com.au/forums/topic/188252-losing-boost-after-4500-rpm/
Share on other sites

When I removed my plenum to inlet manifold gasket I noticed it had been leaking.

When refitting inlet manifold/plenum/throttle body gaskets I gave them a spray with Hylomar just incase.

Using Hylomar also helps should you have to pull it apart again; it prevents gaskets ripping etc so you can save a few $$ and reuse. :(

When I removed my plenum to inlet manifold gasket I noticed it had been leaking.

When refitting inlet manifold/plenum/throttle body gaskets I gave them a spray with Hylomar just incase.

Using Hylomar also helps should you have to pull it apart again; it prevents gaskets ripping etc so you can save a few $$ and reuse. :(

could you haer a sucking sound coming from the plenum when it was leaking.

could you haer a sucking sound coming from the plenum when it was leaking.

I can hear a sucking or hissing type sound coming from my plenum at the moment. Didn't know what it was though, just thought it may have been normal. Guess my plenum is leaking then?

Edited by Simmo1985

Would a leaking plenum cause any other problems? Just trying to figure out if that is in fact the problem, because the car drives perfectly normal otherwise.

Edited by Simmo1985
could you haer a sucking sound coming from the plenum when it was leaking.

No strange sucking noises apart from the usual idle sssshhh noise :)

I think mine was only leaking on boost as it didn't cause any strange idle issues or afm readings.

i got this same problem, i hear a loud hissing like noise come from the plenum at high boost and notice my PSI drop from 20 to 15.. I still haven't got around to pulling the plenum apart and changing the gasket, but i'm pretty sure thats the problem..

  • 3 months later...

I think I have a similar problem. Had it tuned running 18psi no worries but after a week of driving it doesn't seem to hold boost. After 6000rpm the boost drops from 18psi to about 5psi. I can't hear any strange noises though..

I dont think its the inlet sucking closed as I placed a metal pipe in part of it. It looks a little weepy round the plenum gasket. Hopefully thats it..

ANYone got the part no. for R33gtst?

Edited by benl1981

The mechanic reckons I should just change the gasket without even running it on the dyno. They reckon theyve seen a lot of this on the rb25s. It isn't always that easy to hear apparently - and under load there is so much air floating around there with the fan going etc..

Will have a bit more of a check myself..

Nissan want $85 for one! There was a little oil residue around the join. We cleaned this off but there isn't really much coming back. Might run it up onto boost a few times and check again. I did a few 0-100km/h runs the other day which may have blown it apart..

Edited by benl1981

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...