Jump to content
SAU Community

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

don't be a fool man

haven't you been listening @ all

R12 is for R12 systems

R134a is for R134a systems

DONT mix the two or your compressor wont like it

my mate also says you cant get R12 anymore and its been like that for years so if there saying its R12 its prolly one of the substitutes

if you want to waste $170 on getting that then go right ahead but i did tell you earlier my mate can do it for $50

Edited by Madaz
hrmm the place you told me, down lonsdale. alright madaz can u ask ur mate if he can regas mine than and when and where could he do it. thanks

ok mate, just rang him he said by next weekend as hes on holidays and will go into work next week and get some gas

If you have r12 which is an old gas you will need to swap it over to the new gas R134a

and if you need a regas you have a leak.

so you need to pump some nitro through it to see where it is. most of the time its the o rings on the flair nuts so just tighten so of the connections and hose fittings up.

To see if you need some refrigerant check the sight glass on the silver tank looking thing [drier] and see if its got a full charge of liquid do this while the car is running and the AC is on. also check to see if your condenser fan kicks in.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
×
×
  • Create New...