Jump to content
SAU Community

Recommended Posts

yeah im thinking i want to do the same

anyone have a R33 stock air box would like to swap for pod filter

PM me will put up in the wanted section later

I believe so! I've got a HKS pod under it. Its only there to appear stock ... so is the rest of the work to the bay. Got to keep it looking stock as a bone :)

I'm also replacing my plugs and ensuring the gap is 0.8mm.

Mmmmm ... coilpacks :D

With coppers. Best/cheapest place to grab them is Motor Traders at around $2.85 per plug. Else where pay the usual $4.40 per plug. Which really isn't that much anyway.

RB20/25/26

BCPR6E for stock power to around 250-300rwkw. 0.8mm pregapped.

BKR7E-11 for powers 250rwkw+. 1.1mm pregapped need to gap down to 0.6-0.8mm depending on boost.

The two above plugs are the v-groove type.

I find they last a good 20,000km's. By 30,000km's they are beginning to look quite rounded. :)

I run the BKR7E's have absolutely no issues with fouling. At 268rwkw the BCPR6E's were coming out a looking a little hot, the BKR7E's heat range is spot on and look nicely tanned.

If you have issues with fouling the car is running way too rich and really should be sorted.

doing some window shopping :)

http://www.j-spec.com.au/list/index.php?ID=13050

http://www.j-spec.com.au/list/index.php?ID=12821

one needs a bit of an engine bay clean up but is cheap!

Edited by Damo_R34

ok i took my coilpack cover off....

started the car waited 20mins or so to hit full operating temp...

nothing...

so i drove it and still NOTHING

so i have come to the conclusion that it may be getting hot under the cover at full opp temp?

i guess i drive it with the cover off till my spitfires arrive.. is it ok to leave the cover off??

and i correct in saying that this was prob the problem?

cheers

no, 120 the set, Simon32 says just get copper there fine you just may need to replace them sooner

iridiums are meant to last longer thats why there dearer oh and there made of iridium i guess

blow me down! i just ripped one out and its ngk irridum.. looks fairly clean and its gapped to 1.0 or something, will close them all down to 0.7 and see how i go.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I refer you to this thread on PF, by someone who knows what he's doing. Paints a good picture of the humble AD09.
    • Ha, I've never pressed the X in all these years incase it removed the notification for all Admins
    • I don't know, I've never done it that way, but 1. While it is an interference engine, there is still clearance between the valves and the piston at all points in the regular timing cycle 2. There is not a lot of distance before you can't catch the top of the valve stem any more I don't know if 2 is greater or less than 1. But 3. If it doesn't work out you are f**ked, engine is coming out to disassemble so it is a big bet.
    • Semi slicks are horrible for road use, just use a high performance road tyre unless you really need the maximum grip. Noisy, unpredictable (amazing, until they are not), expensive due to very high wear and not good in cold and particular wet. And yes, it is a thing to store cars on stands instead of tyres if you know they are going to be parked up long term.....but who ever realises that a short park is going to stretch into years before it is out again!
    • I know in Australia you'll definitely get above 30c. Parked in the shade in Summer you'll be above that. 😛 But in cooler climates, you might get that warm driving on the highway for a bit, but you'd never get to full heat temp. I'll try and find some of my historical tyre temps between Aus summer and winter (be aware immin the warmer area of Aus too.)
×
×
  • Create New...