Jump to content
SAU Community

The Sa Wasteland

Cubes

By Cubes,
in South Australia

 Share

Recommended Posts

  • Replies 36k
  • Created
  • Last Reply

Top Posters In This Topic

  • Damo_R34

    2820

  • scandyflick

    2266

  • Madaz

    1919

  • craig R33

    1717

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Ryanrb25
Ryanrb25

i went for a hills run last night in the 31 with the roads very slippery.....was much fun. Had to bed in the bottom end bearings so yea..took it for a strap.

DSTROY
DSTROY

Hey Ryan, do you know how to fit a set of drop spindles to the front of a hilux???

Madaz
Madaz

Dam straight Damo would rather do SAU them heroin gts4 are 4.1 because they share the same parts from the gtr i think r32 gtst is 4.3 because of the lack of torque from the rb20

Posted Images

Madaz Grand Master

Madaz

Posted
Posted

while your doing that might as well slap a turbo on it :)

You'll need to remove the head if thats the case. Might as well throw a gasket kit at it while you're there, just to be sure. Drop the sump and replace the con bearings while you're there ... hell, re-ring it too. Check for abnormal wear and tear.

Best to spend an extra day and $300 freshening up the motor, just to be sure.

I did it will all my engines I picked up for cheap. :D

edit: oh, while the head is off, remove the valves and clean them up too.

your curve Joel from like 95 is like hold on and enjoy the ride :D

For Rad33 with his new rb25det on the way.. Get an rb30 under it. :P

RB25det vct head FTW for bottom end. :D

AL's motor is running the same GT3076 .82 on an rb30det but with a nice exhaust and inlet manifold with slightly smaller cams. The VCT has picked up some nice low end power peak power appears to be made around 7000rpm.

Now for mine.. :P 15.5psi that can be seen and the last tune at 19.5psi through the mid that tails off to 17psi causing top end to flatten out. The 2" fmic piping is causing issues up top as well as the wastegate flap being blown open.

Mine makes its peak around 6000rpm. Will play with the adj. cam gears to shift that to approx 6500rpm. :D

lol we could of told you that cars never miss behave once you get them to the mechanics - PM send about AFM's

So when the mechanics drive my car it doesnt shit itself?????????? FFS!

so where does that leave me? high and dry.

the only thing i can do is.... what for it to happen again and make sure it happens at the mechanics?

ill have to try and clean out the AFMs and check for damage.

Damo :D

sandninjas.jpg

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...