Jump to content
SAU Community

Recommended Posts

hmm, car payout figure 19,291, sell it and buy s14/r32 and buy house, or keep? ;)

Keep black rims, buy my car, flare, straight pipes, massive camber= awesome..

And a house to take all the drift groupies back too.

Hey,

Does anyone know how to get the faded stuff off the headlights when its on the inside? I use cut and polish to make them clear on the outside but one of them must have had mosture on the inside at some stage....

Cheeeeeers

Edited by ontheranch
Yeah agree

wtf damo vegemite

nothing better then canadian mayple syrup mate and whipped cream

it was all homemade bar the syrup

im one for honey or strawberry jam with cream...

syrups are too darn sweet. and it has to be pancakes or crepes, pikelets are shit

vegemite. wtf man.... surely your parents arent *that* poor?

-D

you have to take the headlight out, and put it in the oven so it softens the glue thats holding the lens on. when it softens, peel the lens off and clean, then re-attach with glue.

and lol, i enjoy vegemite on my pancakes, you havennt lived til you've tried it. And i DONT like maple syrup (canadian or otherwise) or cream, so no point my parents buying it!

you have to take the headlight out, and put it in the oven so it softens the glue thats holding the lens on. when it softens, peel the lens off and clean, then re-attach with glue.

Have you had to do it before?

To be honest I wouldnt trust myself doing something like this!

you have changed damo lol

nah your just plain f**kin weird man lol

the only time i would eat vegemite is before a big night on the booze

thats about it and only then....which seems to happen quite often though

i eat vegemite all the time, to not eat it is un-Australian.

And Penny, i haven't done it before, and i have searched in quite a few places to find new headlight lenses, but to no avail.

i eat vegemite all the time, to not eat it is un-Australian.

And Penny, i haven't done it before, and i have searched in quite a few places to find new headlight lenses, but to no avail.

Vegemite does indeed have its place. On toast and the like...

I sure hope you're not the type of solsbreeite who puts vegemite on pasta and ice cream?

-D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...