Jump to content
SAU Community

Recommended Posts

wouldnt of thought NA RB would have enough power to utilise the RON

i didnt wanna say it.

LOL that's what i would have thought?

What static compression do they run?

9:1 afaik.

just for comparison, my old toyota ran a cr of 10.5:1 and didnt have any problems on any premium fuel. cant see how the lower compression nissan engine would suffer problems.

my car lost power with the v-power fuel, she hated it ran like crap and detonated off her nut :laugh:

I'd be taking her to the mechanic in that case, could be many other things like spark, coil packs, afm ect ect....

Mine runs just fine on V Power, I wouldn't say it runs better (than Ultimate 98) but I definitely get better fuel consumption on V Power. But I'll use either, depends where and when I fill up... :nyaanyaa:

Well the issue is resolved. Found some octane booster in my shed, put it in this morning and she runs fine now. f**king shit fuel. :nyaanyaa:

Edit: I should add, it doesn't matter if the engine is forced or na, shit fuel is still shit fuel. Don't you think NA cars suffer detonation too?

I've got a new name for V Power: Vagina Power = its a c*nt of a fuel :laugh:

Edited by RubyRS4

almost there. intakes been hooked up, disconnected the cas and cranked it a few times, cant see any leaks, but ill have to wait til i actually start it to know for sure.

just waiting on a couple shorter exhaust studs, and then its start time. getting anxious now. lol.

What servo did you get the V-Power from Ruby? Was it a servo that is very busy? 98 ron fuel (no matter who makes it) will lose octane as it sits. So if it had sat in their tanks for 3-4 weeks because no one had bought it, then it would probably have been down around 95 RON.

The trick is ALWAYS buy your fuel (BP, Shell, Mobil) from a very busy servo. Tanks get drained quick, which always means nice fresh 98 ron fuel.

The same applies if you put you dont drive your car for a while. If it sits for a month or two, ALWAYS add fresh fuel, or at least octane booster before heading off again :nyaanyaa:

Supporting the above, I've use both V-Power and BP Ultimate in all my cars, and each fuel is the same as each other - never a bad batch because I always visit busy servo's on main roads :laugh:

I think I just encountered a bad batch. Still wasn't happy about it.

I always (99.9%) buy my fuel from BP near Greyhounds and BP West Tce, or Shell West Tce

Not sure if I should name the servo ... but its located near the brewery :nyaanyaa:

Edited by RubyRS4

See now that is a pretty shitty small servo - it wouldn't surprise me if the don't sell much 98 there at all and you got some old horrible fuel.

(probably sell plenty of 91 with the 4c dockets for all the dero's heading home to the western suburbs :nyaanyaa:)

Just a quick question...how do i get the static compression ratio of my car???? std rb30 but with a set of hypatec dished pistons??

a compression tester ? if its a built engine, or you can calculate compression based upon measurements,bore,cc of cyl head etc if the motor isnt built yet

how awesome is having 3,333 posts?

not because im a post whore and wanna brag about my fairly large e-penis, i just like having numbers line up.

that and a dollar coin will get you a few min at the car wash to wash your penis dave...the one that counts is the "666" post :nyaanyaa: ...lol

See now that is a pretty shitty small servo - it wouldn't surprise me if the don't sell much 98 there at all and you got some old horrible fuel.

(probably sell plenty of 91 with the 4c dockets for all the dero's heading home to the western suburbs :P )

Aww c'mon ... its right next door to the fully hectik Super Cheap yo! Thats gotta be worth a few extra kw. :nyaanyaa:

Had no choice, right near empty and I failed to stop at BP West Tce. :laugh:

that and a dollar coin will get you a few min at the car wash to wash your penis dave...the one that counts is the "666" post :nyaanyaa: ...lol

the devil is my bitch.

srsly.

ive got a photo around here somewhere...

... anyways, got a price on those work meshies i posted some pages back. bout 1400 beans. be able to sell my enkeis to make up at least half that i reckon.

:EDIT:

for anyone that cares, these are the wheels in question;

4902P5120746.jpg

went out side with a couple rulers, fronts will sit pretty flush with the camber im running at the moment, rears will sit *just* proud with a 5mm slip on, will require some rolling though, and a bit of a lip when i get the camber sorted. jawesome.

Edited by scandyflick
meshies look awesome, def one of my favourite style of rim to suit a skyline or a 2hunj

love VS-XX work or the Weds Kranze mesh - or BBS if youve got the extra coin you dont mind parting with your left testicle, first born son, and soul.

Edited by scandyflick

Ebay find:

A bit too "out there" for my liking. It'd be a cop magnet in Adelaide

http://www.cgi.ebay.com.au/R33-Nissan-Skyline

and here's a fail:

http://www.cgi.ebay.com.au/1999-Nissan-Sky...R34-GT-R-Purple

:dry:

Edited by RubyRS4
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...