Jump to content
SAU Community

Recommended Posts

$220, that was a touch up on an existing tune.

Sweet. Now that I got my fueling and CAS fixed, I wanna get the Stagea on the rollers to get back those lost ponies.

Did a compression check a while ago and thankfully no compression loss or blown rings etc. Thankful that I babied the stag around when I knew it wasn't running right.

I wanna get to that turbo/dump gasket leak this weekend too.

damo that boost curve looks consistent with the r34 turbo

a really good ebc may fix up the peak & hold boost, or better yet a fully tuneable computer

as it is it isnt a bad tune...

i have a power fc, but a shit boost tee.

ah simple then, save for the power fc boost controller - scour ebay, JPS Trading Ltd is a good trader to search thru

you can see where the boost T isnt cutting the mustard from 80-120kmph

see how a decent boost controller works better ?

post-18854-1253667227_thumb.jpg

edit: the dropping off of boost was from restricted exhaust, much flatter now at the pointy end of the graph

tune of new piggyback ecu on 8th Oct, update then with a 250+ kw tune map

If you still have the factory boost solenoid in line then i expect if you had a your boost graphed then this is what it would look like (This is a mates figure from his 33). How much boost are you running? Is yours an auto or manual because that figure looks a bit low to me (depending on boost). The other thing that would be playing a part in the hole is the VTC timing not being perfect.

ZacsDynoFigure.jpg

Edited by D_Stirls

scan0001-2.jpg

still dropping off - but fuelling is the issue here

again, on 8th oct bigger injectors slot in, so will update some graphs for discussion.

Id suggest damo that a better ebc will do the job well. p-fc boost controller.

see how a decent boost controller works better ?

post-18854-1253667227_thumb.jpg

edit: the dropping off of boost was from restricted exhaust, much flatter now at the pointy end of the graph

tune of new piggyback ecu on 8th Oct, update then with a 250+ kw tune map

Where is the dropping off boost shown?

If you still have the factory boost solenoid in line then i expect if you had a your boost graphed then this is what it would look like (This is a mates figure from his 33). How much boost are you running? Is yours an auto or manual because that figure looks a bit low to me (depending on boost). The other thing that would be playing a part in the hole is the VTC timing not being perfect.

The graph says 10-11psi, when he rang i said around 10.5psi would be fine, and i assume thats what its on, hard to read from factory bar guage. Its a manual.

Its a turbosmart bleed valve, and always has lost boost from 4000ish to redline since it was fitted.

:D This is gonna sound pretty gay. But for some reason Damo, You were in a dream of mine last night. And you drove a VT commodore.

Thats sweet Craig. and by "drove a VT Commodore" i hope you mean "watched you have sex with Megan Fox"

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...