Jump to content
SAU Community

Recommended Posts

Been reading for years that the N1 pump just has a higher rated spring over the standard pump

I just read this

www.gtr.co.uk/forum/upload/39978-n1-oil-punp-upgrade.html+N1+oil+pump&hl=en&ct=clnk&cd=5&gl=us

is this true? Or did this person pick up a Nismo pump rather an N1?

thanks!

Link to comment
https://www.sau.com.au/forums/topic/189044-n1-oil-pump-flow-more-than-factory/
Share on other sites

n1 oil pump pumps around 25% more oil than standard. theyre a high flowing oil pump.

if you're using one on a high revving engine make sure you do the oil feed mod to your block as it can empty your entire sump 25% quicker :cool:

high pressure pumps increase oil pressure throughout the rev range.

you can make any oil pump have a harder spring, just tighten the big bolt on it. all this does is raises or lowers the peak oil pressure.

it works on the same principal a wastegate works on.

  • 2 weeks later...

I was under the impression N1 oil pumps flow "LESS" than factory ones.

they are designed for constant hi revs.

and being that the RB's all have oil control problems, where by too much oil gets pushed to the head, the N1 designed for that sort of situation flows LESS.

Same goes for the N1 water pumps compared to other RB water pumps.

thats true but only for the N1 water pumps. they flow less at low rpm because they were designed mainly for vehicles that are track dedicated or vehicles that are driven hard (sustain high revs, often) and are fed a higher volume of water at higher rpm where they spend most of their time.

N1 oil pumps flow more all over the rev range. they are a 'high volume' pump which means more oil and higher pressures. i've got one in my car and my std gauge reads a little higher than what it used to before the build.

Well the thing is I've always *read* the n1 pump just has a higher rated spring. I've never came across something otherwise until recently. Even sydneykid said so himself

http://www.skylinesaustralia.com/forums/in...t&p=1668325

Higher pressure doesn't substaniated higher volume. You can have higher pressure with the same volume.

Edited by maximajim

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...