Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm clearing out some of the larger bits and pieces from my garage as they are taking up too much space.

Stock stuff

Bonnet sold

R32GTSt driver side front guard, gunmetal, straight, paint in good condition with a few minor blemishes and light scratches. compliance indicators are still installed $75

post-2863-1192318735_thumb.jpg

R32GTSt passenger side front guard, gunmetal, slight kink where the tyre nicked the guard at a skid pan day but barely noticeable, paint ok, compliance indicators still installed $65

post-2863-1192318792_thumb.jpg

R32GTSt stock rims with shot tyres. I think they are in reasonable condition, there's almost certainly some gutter rash but i haven't looked closely in the last few years since they were taken off. $200 for the 4

post-2863-1192318901_thumb.jpgpost-2863-1192318958_thumb.jpg

R33GTSt front half of the manual tail shaft, i got it to pinch the yoke for my gear box swap, ended up getting a new one. $25.

Performance stuff

M's K&N pod. One of the big ones including the adapter to bolt to the stock afm. Also fits z32 afm. used. looks to be in reasonable condition $50

post-2863-1192282101_thumb.jpg

X Force 3.5 inch straight through cannon. Universal fit, brand new, never used (the plug has been used as it fit my current exhaust) $100

post-2863-1192282240_thumb.jpg

I'll post some more pics up tomorrow when the light is better.

All prices ono. Pick up only at Campbelltown NSW for the stock stuff as it's just too big/heavy/easily damaged for postage. pod can be posted at buyers expense.

Thats all i can think of atm

cheers

Dave

post-2863-1192318629_thumb.jpg

Edited by BHDave
Link to comment
https://www.sau.com.au/forums/topic/189164-r32gtst-bonnet-guards-rims-ms-pod/
Share on other sites

pics added.

Dave, 2 of the wheels have no rash and are in surprisingly good condition, one has a very small mark on the lip and one has a bit of rash (i've added a photo of the rash).

cheers

Dave

i will have in a week or so, just waiting on my gtr ones to arrive. The top mount has snapped off where the screw goes through but i've just had a big washer on there holding it in place for the last 3 years with no problem

Where abouts in sydney do you live becuase i'll take that bonnet asap, if you could drop it off to my house i would be happy to pay $200, i am located near North Richmond, thanks

sorry whyte, the r32 and r33 front halfs are completely different. The r32 has the center bearing on the front half and the r33 has it on the back half from memory (or vice versa). The yoke size is different as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...