Jump to content
SAU Community

Recommended Posts

3.jpg

PictureCeffy1.jpg

rims.jpg

2005_0104Image0011.jpg

Driveline:

RB20DET

RB25DET gearbox

OS Twin plate & light weight flywheel

2-Way LSD

HKS T04e

HKS cast manifold

HKS 38mm external gate with screamer

Wolf 3D v4 ECU

Blitz stainless air filter

Custom stainless crossover & turbo outlet pipes

Loud in tank pump

GTR injectors

GTR intercooler

Trust Type R BOV

RSR* exhaust

Splitfire coil packs

Modified rad support housing triple core TR's radiator

Twin thermo's (tempreture controlled via ecu)

ARC oil cooler + Grex filter relocation

Sard header tank

Cusco oil breather

Suspension/Handling:

Seam welded

GET coilovers with camber tops

Tein castor rods

Cusco rear upper arms

Cusco rear swaybar

Rear traction rods

Welded rear strut brace

Non HICAS cradle

Alloy cradle bushes

Alloy steering spacer

5 stud conversion

Interior:

Thrash style fixed back seat

Rare Abarth leather wheel

Omori Oil pressure, Omori water temp, Greddy oil temp, Blitz boost gauges in custom dash panel

Profec-A EBC

Exterior:

Pearl blue paint

Missile front bar (missing lip)

Insurance DIANA skirts and rear bar

Yanack bonnet vent

Bolt-on flares smoothed over

Late model front/rear lights and grill

Stich Evolution 18x10 +18 front, 18x11 -1 rear

Falken Azenis ST115 tyres with good tread

Other stuff:

Factory sunroof

Fully rebuilt tailshaft

Jap workshop & club stickers

Bad bits:

Uncomplied, 15 yr import approval will be supplied.

Guards could do with attention.

Clutch isn't disengaging fully. This started happening straight after new engine was installed. Suspect snapped release pivot which is a cheap replacement.

Only on basic tune atm. 220 rwhp on 9 psi. No where near turbo's efficiency.

$10500 FIRM. Very unique vehicle. As far as I know the only Cefiro in Aus with Insurance skirts and/or rear bar. In saying that don't expect show quality body and paint, it's a pig.

[email protected]

0415291321

Edited by D-limo
Link to comment
https://www.sau.com.au/forums/topic/189641-fs-jap-spec-cefiro/
Share on other sites

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

All work done in Japan. Tokage can get them not sure if they are the same size might be a bit smaller. Or Yahoo auctions. It's a mission though if you still want the rear doors to open like mine. Your guards are pumped and hot already aren't they?... Just find some good offsets and it will be sex.

  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...
  • 4 weeks later...
i cannot beleive nobody's bought this??

it's so cheap it'd make a WICKED race car...

I think the non compliance issue is scaring people away.. $800 and a bit of effort and you have an off tap street car.

At this price it doesn't worry me too much if it doesn't sell. I just wish if it does, it be sooner rather than later :blush:

so cheap and so tempting...

you know u wanna!, you miss the ceffy chassis?

this is one cefiro that could pull off uras aero.

10k is a bargin...i dont have 10k :D

+1 :banana::D

I think the non compliance issue is scaring people away.. $800 and a bit of effort and you have an off tap street car.

At this price it doesn't worry me too much if it doesn't sell. I just wish if it does, it be sooner rather than later :D

just the wrong time of year to sell i think mate, nice car though, id own it if i had the $$ . also i think t04z and rb20 scare people off too tbh, is it laggy?

my mates got a T04Z on his RB20 with tomei cams and makes fullboost around 5k, but man does it hit hard, sounds nuts too. just rb25 the farker, use the same turbo, wack some uras aero on it, smash it on the ground, then drift the shite out of it. done and DONE.

sooo...whos got 10k to lend? :thumbsup:

It's a T04E from ye old school.. Starts spooling just before 4k. Screamer sounds fantastic at low boost...From what I've gathered turbo is rated at about 500-520hp.

Sorry but Diana owns Uras :thumbsup: In person the lines just look sex. She's JDM low already too :P

The only other Cefiro in the country with similar guards is the purple one running the RB26 that appeared in HPI.. That car got wrecked when they fitted Uras IMO

Edited by D-limo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...