Jump to content
SAU Community

Recommended Posts

3.jpg

PictureCeffy1.jpg

rims.jpg

2005_0104Image0011.jpg

Driveline:

RB20DET

RB25DET gearbox

OS Twin plate & light weight flywheel

2-Way LSD

HKS T04e

HKS cast manifold

HKS 38mm external gate with screamer

Wolf 3D v4 ECU

Blitz stainless air filter

Custom stainless crossover & turbo outlet pipes

Loud in tank pump

GTR injectors

GTR intercooler

Trust Type R BOV

RSR* exhaust

Splitfire coil packs

Modified rad support housing triple core TR's radiator

Twin thermo's (tempreture controlled via ecu)

ARC oil cooler + Grex filter relocation

Sard header tank

Cusco oil breather

Suspension/Handling:

Seam welded

GET coilovers with camber tops

Tein castor rods

Cusco rear upper arms

Cusco rear swaybar

Rear traction rods

Welded rear strut brace

Non HICAS cradle

Alloy cradle bushes

Alloy steering spacer

5 stud conversion

Interior:

Thrash style fixed back seat

Rare Abarth leather wheel

Omori Oil pressure, Omori water temp, Greddy oil temp, Blitz boost gauges in custom dash panel

Profec-A EBC

Exterior:

Pearl blue paint

Missile front bar (missing lip)

Insurance DIANA skirts and rear bar

Yanack bonnet vent

Bolt-on flares smoothed over

Late model front/rear lights and grill

Stich Evolution 18x10 +18 front, 18x11 -1 rear

Falken Azenis ST115 tyres with good tread

Other stuff:

Factory sunroof

Fully rebuilt tailshaft

Jap workshop & club stickers

Bad bits:

Uncomplied, 15 yr import approval will be supplied.

Guards could do with attention.

Clutch isn't disengaging fully. This started happening straight after new engine was installed. Suspect snapped release pivot which is a cheap replacement.

Only on basic tune atm. 220 rwhp on 9 psi. No where near turbo's efficiency.

$10500 FIRM. Very unique vehicle. As far as I know the only Cefiro in Aus with Insurance skirts and/or rear bar. In saying that don't expect show quality body and paint, it's a pig.

[email protected]

0415291321

Edited by D-limo
Link to comment
https://www.sau.com.au/forums/topic/189641-fs-jap-spec-cefiro/
Share on other sites

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

All work done in Japan. Tokage can get them not sure if they are the same size might be a bit smaller. Or Yahoo auctions. It's a mission though if you still want the rear doors to open like mine. Your guards are pumped and hot already aren't they?... Just find some good offsets and it will be sex.

  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...
  • 4 weeks later...
i cannot beleive nobody's bought this??

it's so cheap it'd make a WICKED race car...

I think the non compliance issue is scaring people away.. $800 and a bit of effort and you have an off tap street car.

At this price it doesn't worry me too much if it doesn't sell. I just wish if it does, it be sooner rather than later :blush:

so cheap and so tempting...

you know u wanna!, you miss the ceffy chassis?

this is one cefiro that could pull off uras aero.

10k is a bargin...i dont have 10k :D

+1 :banana::D

I think the non compliance issue is scaring people away.. $800 and a bit of effort and you have an off tap street car.

At this price it doesn't worry me too much if it doesn't sell. I just wish if it does, it be sooner rather than later :D

just the wrong time of year to sell i think mate, nice car though, id own it if i had the $$ . also i think t04z and rb20 scare people off too tbh, is it laggy?

my mates got a T04Z on his RB20 with tomei cams and makes fullboost around 5k, but man does it hit hard, sounds nuts too. just rb25 the farker, use the same turbo, wack some uras aero on it, smash it on the ground, then drift the shite out of it. done and DONE.

sooo...whos got 10k to lend? :thumbsup:

It's a T04E from ye old school.. Starts spooling just before 4k. Screamer sounds fantastic at low boost...From what I've gathered turbo is rated at about 500-520hp.

Sorry but Diana owns Uras :thumbsup: In person the lines just look sex. She's JDM low already too :P

The only other Cefiro in the country with similar guards is the purple one running the RB26 that appeared in HPI.. That car got wrecked when they fitted Uras IMO

Edited by D-limo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...