Jump to content
SAU Community

Recommended Posts

Hey there,

The last two of nights when leaving work (11pm) the car has been blowing a large amount of white smoke from the exhaust system. I'm not sure why, hence the reason for this post.

The car is a 1993 Nissan Skyline GTST

I've only noticed this white smoke on Tuesday night but didn't take too much notice thinking it was just because it was cold. But, It's happed again tonight and it's got me worried as its a little more then usuall on cold start-ups.

The car didn't seem to have any of this white smoke during the day - on start up or driving down to the local Autobarn.

Recently the car has had an oil change, oil filiter change and a few weeks before that had a complete coolant flush as the Water Pump needed to be replaced.

The car has also had a complete forged rebuild about 5 months ago, and also a Haltetc ECU installed about 2 months ago - I'm also running the stock turbo.

Tomorrow I guess I'm going to start with cleaning the intercooler pipes and probably check the spark plugs while I'm at it. Also have a small coolant leak which I'll also fix tomorrow.

Only other thing I think it maybe is the turbo seals, but honestly I hope its not!

I've tried to provide as much information as I could, but any questions or anything I'd be more then happy to answer them - really want this issue fixed :D

Thanks again,

Aron

Link to comment
https://www.sau.com.au/forums/topic/189885-white-smoke-on-cold-start-up/
Share on other sites

white smoke = oil in exhaust,

now forged pistons, do expand quite alot from hot 2 cold compared to cast pistons and others, so ona cold motor the piston will b rather loose in the cylinder (some people even have knockin etc) maybe the oil you put in on the last oil change is a little thin and by-passing the rings when cold...

but most likely ur turbo seals are stuffed lol

white smoke = oil in exhaust,

now forged pistons, do expand quite alot from hot 2 cold compared to cast pistons and others, so ona cold motor the piston will b rather loose in the cylinder (some people even have knockin etc) maybe the oil you put in on the last oil change is a little thin and by-passing the rings when cold...

but most likely ur turbo seals are stuffed lol

Is this whilst driving? Idle? or load? plus noticed your in brissy, we have had some relative humidity lately at night time it could be condesation. need more info as per above

white smoke = oil in exhaust,

now forged pistons, do expand quite alot from hot 2 cold compared to cast pistons and others, so ona cold motor the piston will b rather loose in the cylinder (some people even have knockin etc) maybe the oil you put in on the last oil change is a little thin and by-passing the rings when cold...

but most likely ur turbo seals are stuffed lol

I've used Royal Purple SAE 10W-40 for quite a few months and never had this problem.

Is this whilst driving? Idle? or load? plus noticed your in brissy, we have had some relative humidity lately at night time it could be condesation. need more info as per above

It's while the car is idle, once I'm driving I can't notice any white smoke but it's hard to tell when your in the drivers seat.

-_-StRyDeR-_-[/b]]i get the same, only in winter though lol. its condensation

Even on really cold start ups, colder then the last two nights I haven't had this problem. However, I noticed only one drip of condensation/water from the tip of the exhaust.

Edited by KustomR33

Alrighty, here's just an update,

I've fixed that coolant leak I had, I had another look at the white smoke I started it up this morning when the car was cold, and there is a minimal amount of white smoke, probably from the cold start?

Took it for another drive, power seems good, if not better then usual - I guess I'll have to see if it smokes tonight after work while letting the car warm up.

I don't think its the turbo seals, because if it was it'd be doing it all the time.

It could be the valve stem seals because it only happens when the car is cold, but its only happing at night so its confusing.

Maybe there's a little bit of oil in the intercooler piping? I'll give that a clean soon see if that gets rid of it.

Or, lastly, could just be my head :lol:

If anyone has any other ideas, suggestions please do let me know :)

Thank-you very much for your help.

White smoke on a cold start is more than likely water vapour condensing in the cooler outside air (the compustion process produces water, amongts other things).

But, not large amounts like I'm getting at night on cold starts?

White smoke is not from oil.. Blue smoke is oil smoke so i dont think it's blow by past your rings even with forgies these days thermal flex isnt like it used to be so i doubt it's that, or your valve stem seals.

good luck though come us updated but.

is it smoke or steam, next time it happens watch it as it comes out of the pipe, if it disapears after a meter or 2 its steam, if it hangs around in a cloud for a few meters its smoke.

When I first start the car it's steam, after a couple of minutes it becomes smoke.

White smoke is not from oil.. Blue smoke is oil smoke so i dont think it's blow by past your rings even with forgies these days thermal flex isnt like it used to be so i doubt it's that, or your valve stem seals.

good luck though come us updated but.

Here's the latest;

Started the car tonight at work to let it warm up as usual, noticed white smoke again, reved the car a little bit and I got alot more white smoke and black smoke too.

It also smells like oil/fuel..

Could it be a bad dose of fuel?

Hey man what sort of breather system is on your motor? ie catch can?

my car went for a few weeks blowing white smoke similar to yours, it turns out the cank case was pressurising due to blocked breather lines. this was causing oil to blow out the rear turbo seal.

doesn't sound right but when I replaced the hoses to the catch can it went away :)

have a look!

Hey man what sort of breather system is on your motor? ie catch can?

my car went for a few weeks blowing white smoke similar to yours, it turns out the cank case was pressurising due to blocked breather lines. this was causing oil to blow out the rear turbo seal.

doesn't sound right but when I replaced the hoses to the catch can it went away :)

have a look!

I'll check my breather hoses today, but I don't have a catch can on the car though.

By the way, thanks to everyone who has been trying to help me :D

Hopefully I can get it sorted soon.

Edited by KustomR33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...