Jump to content
SAU Community

Recommended Posts

Hey guys, recently received a major defect which requires a RWC, however I just got a RWC 1-2 weeks ago, hence it is still valid.

If I just take the RWC cert into vicroads will they let me clear the defect? Or does the RWC have to be obtained after the date of defect?

Cheers, bry

Link to comment
https://www.sau.com.au/forums/topic/190302-defected-with-a-valid-rwc/
Share on other sites

Assuming that the RWC is still valid (i think they are valid for 30 days but could be wrong) then take it together with the defect notice to whoever issued you the RWC.

They need to determine if the items listed on the defect notice were covered by the original RWC and were not overlooked.

If they were overlooked then those items need to be fixed, if the RWC issuer feels that they were covered then you can go to Vic Roads and show them your RWC.

Note: you are doing the issuer of the RWC a favour by doing this b/c if you went to Vic Roads and just showed them the RWC and the items listed on the defect notice were in fact overlooked on the RWC, then the mechanic/workshop could be investigated (esp if there have been other instances like this by this workshop) and could potentially lose their RWC licence.

So it is in the best interest of the RWC workshop to fix any items at little or no expense to you given that they overlooked this in the first place and have inconvenienced you now and b/c you are doing them a favour by not going straight to Vic Roads.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...