Jump to content
SAU Community

R32 Gtr Stalling Then Not Starting

TAS_SINFUL
 Share

Recommended Posts

TAS_SINFUL Collaborator

TAS_SINFUL

Posted
Posted

Hey guys, my GTR which is pretty much stock (including ECU) will start fine when its dead cold and it runs perfect for like 10 mins.

once it gets up to normal temp it just stall itself and wont start again untill its been left overnight and gone cold again.

the only thing that has been done to its is last month i had my surge tank and 044 installed ready for new injectors and ECU and tune up..but it was running fine with that installed for weeks.

im not really sure at all whats causing it, but my guesses so far have been perhaps AFM, Coil Packs, water temp sensor, igniter module getting too hot, maybe is it possible fuel lines are getting too hot and creating vapour lock in the rail.?

at the moment the car is left sitting in the car wash down the road from my house until i can arrange to get it moved or fixed.

and help would be much appriciated.!

thankyou :nyaanyaa:

Link to comment
https://www.sau.com.au/forums/topic/190535-r32-gtr-stalling-then-not-starting/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

The ignitor modules are becoming notorious for failing with age and heat. When the engine stops, try chilling the ignitor somehow, see if the engine will re-start (maybe even try with bonnet up).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...