Jump to content
SAU Community

Recommended Posts

As stated bits from half cuts:

PHOTOS FURTHER DOWN!!

Not including freight unless otherwise stated!!

BNR32 GTR Computers (Veilside, Access, Standard) $450 each ###OFFERS###

BNR32 GTR Center Instrument/Guage Cluster (two of) $200 Each

BNR32 GTR Rear Seat, Not faded, very good condition $250 ###REDUCED####

BNR32 GTR Passengers guard x2 (one red one is black both good to bolt straight on) $450 each ***1xSOLD, 1xREMAINING*****

BNR32 GTR Front Drivers Guard (slight Damage, undercoated, needs repair) $250 *****SOLD*******

BNR32 GTR Gearbox APPROX $2000

BNR32 GTR Standard Air Box $200 #####REDUCED#####

BNR32 GTR Front Pipes (standard) $200 #####REDUCED#####

BNR32 GTR Dash (good condition) $200 *****SOLD*****

R32 GTS-T Standard wheels with 50% Tyres $720 Incl. freight #####REDUCED#####

R32 GTS-T Enkei 5 Stud Rims 50% Front 20% Rear tyres ******SOLD******

R32 GTS-4 Short Shoft kit (bolts ontop of standard gearbox) $200

ECR-33 GTS-T Full stainless steel cat back exhaust $550

Space Saver spare wheels (yellow in coloour on Toyota PRIUS remaining) $50

BNR34 GTR Rims, damaged, no tyres, only 2 rims (good for hose reels or somethings similar) Pics Below *****SOLD*****

AUTOSPORT KEVLAR RACE SEAT, GTI-R pulsar rail, can be modifed to fit skyline *****SOLD********

Volvo Truck Intercoler, (a bit bigger than a TRUST drag core) $300 Incl. Freight

Huge Truck Turbo (not good for any car application it is about 400mm across, GOOD FOR COFFEE TABLE) Pics Below $200

Regards,

Tom

Link to comment
https://www.sau.com.au/forums/topic/19099-bnr32-gtr-bits-and-pieces/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

CATERPILLAR diesel turbo

Bloody Massive!!

Would make a good coffee table if you put some glass on top of it!

My shoe in the photograph gives you an indication of its size....

Will prob cost about $80 to freight due to its weight!

Good for all those turbo freaks out there, this will impress the boys!

Tom

Originally posted by BNR32

BNR34 GTR RIMS x 2.....

DAMAGED, UNSURE IF REPAIRABLE!

GOOD FOR HOSEREELS OR SOMETHING OR MAKE SOME BUCKS IF YOU CAN REPAIR THEM!!

Email me for price: [email protected]

Regards

Tom

do you have the caps?? also can you get a close up photo cause i cant really see how deep those scratches are??

Prices have been updated for the ENKEI Rims, i got the go ahead to sell them for $1200 incl. freight

Also, standard GTS-T rims for $820 incl . freight and there have been some other ad-ins, just scroll to the top and check and also check out the pictures

Tom

The whole list has now been updated with prices for every part.....

This should provke a little more interest......

Oh yeah, also selling the shells that the parts came from, got the following:

-R32 GTS-4 x1

-R32 GTS-T x1

-BNR32 GTR x 2

-R33 GTS-T x1

-PRIUS

-180SX Type X x1

Dont know what i want for the shells, but the rails and tunnel and bits and pieces are worth money if you prang your car and want to fix it.... A couple of the cuts have been butchered for rails already though...

Tom

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • No need to replace the cover if it is still intact (not worn through). It would be worth checking the balancer for matching marks on the rear, but I'd assume the balancer was loose at some stage. The cam timing marks look fine, once you put the new belt on you can only be right or a full tooth out
    • Disconnecting rods! must have been an unpleasant surprise...
    • So been ocd with timing mark but checked from few angle and seems both cam are on and crank is matching as well to the slot on sump and crank pully   i noticed crankshaft cover has been robbed as per attached pic. Any ideas why? Could my balancer or harmonic be on its way out? should I replace the cover? https://ibb.co/ZR1JFYRR
    • So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
×
×
  • Create New...