Jump to content
SAU Community

Recommended Posts

Make:nissan skyline

Model:r33 gtst

Milage:120,000 (75,000 on motor)

Colour:black

Location:mildura vic

RWC supplied?can be

Currently registered?TEAZN

Price:17,000 without wheels price drop to 16k with wheels

Contact:0438069499 or pm thru here

Comments / Modifications:

r33 gtst

400r kit all round

wider rear guards

wider front guards

work 19"x9.5 wheels all round

red sass seats

black dash

new gates timing belt

guages in dash passanger side

apexi boost guage piller mounted

nismo gear knob

in cabin strut brace

under bonnet strut brace

gtr wing

600x300x100 fmic

stainless steel piping

red cam covers and timing belt cover

silicon intake pipe

k&n air pod filter

resprayed engine bay gloss black

split stainless dump pipe with catco hi flow cat

3" zaughst with twin mufflers

new standard motor series 2 only 75,000klms old

apexi avcr

kazz 2 way diff with rpyal purple oil

new front brake pads and mechined rotors

new rear pads (not yet put in)

greddy type r bov

custom boot install

inverted 12" kenwood sub

bosch 044 motorsport pump with 1.5lt surge tank

standard gtst lift pump

stainless steel teflon fuel line

jaycar amp

clarion front and rear splits

lovell lowered springs

extreme heavy duty clutch

splitfire coil packs

uras pinapples

car has being pretty much resprayed since putting the wider guards on

i also have a heap of spares to put in with the sale

post-17846-1202604648_thumb.jpgpost-17846-1202604660_thumb.jpgpost-10725-1124077567.jpgpost-17846-1202604695_thumb.jpgpost-17846-1202604709_thumb.jpg

post-17846-1202604671_thumb.jpg

Edited by teazn_r33
Link to comment
https://www.sau.com.au/forums/topic/191127-r33-gtst-new-pics-up-finally/
Share on other sites

  • 2 weeks later...
  • 2 months later...
just a quick question...

did u roll your guards to get them that wide or was it an add on kit.....or total replacement of both front and rear guards???

the rear have being pumped out and wider ones put over the top

Love the wheels......

Cars tough too!

thanks man they were for sale a while ago

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...