Jump to content
SAU Community

Recommended Posts

Hey guys and gals, i've just recently joined the the forums, and I'd like to introduce myself. My name is Roald, but you can all call me Roo.... its easier :)

Now, I don't drive a skyline, but i do have a RB30DET (25/30) in my VL Calais, and I figured this would be a good place to get some good info on the newer nissan tech, as the VL sites i've become accustom to are more 'SOHC oriented'....

I have some Q's regarding my setup etc. but I'll get to them at a later date (studying....)

Looking forward to getting involved,

Regards, Roo ;)

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/
Share on other sites

  • 4 weeks later...

Ok, so its been a while.... I've been busy finishing my CIT course - flat out!

Here are some pics and info from the prevoius owner. I would have loved to do the conversion myself, but this came along and was far more cost effective :)

Engine

7,000 km's old

3ltr, acid cleaned, crack tested

bored and honed 50 tho to suit oversized pistons,

shot peened rods. New mains, big ends, small ends, balanced etc.

genuine Nissan head gasket

reconditioned RB25DET cylinder head with extra provision for VCT,

ceramic T3 turbo driven only on 6 psi

3inch exhaust with high flow cat

New bosch 910 fuel pump

Custom braided lines for turbo

Nizpro engine bay mounted intercooler

Wiring harness professionally modified to suit vl

Gearbox

R33 turbo 5speed manual box

Pulled down for inspection before fitting

Short shifter

Harness and speedo modified to suit vl

Heavy duty clutch,

shaved flywheel,

Fully balanced and modified drive shaft to suit r33 box

148RWkW and 530Nm on 6 PSI, std. R33 computer :)

Will get more pics up later on some time.

Cheers, Roo

post-43945-1196227870_thumb.jpg

post-43945-1196227880_thumb.jpg

post-43945-1196227887_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3502555
Share on other sites

148rwkw? :huh:

Are you sure that figure is correct? You should be making a lot more than that...

No offence intended.

None taken :) .The reason for such odd Power vs. Torque figures is due to a rather restrictive intercooler. Between about 2100-3300 rpm I have access to full boost (10p.s.i), but by the time I've reached 4500 rpm its all the way back at 6 p.s.i :) You can see on the dyno sheet where the boost really falls off. Once its gets up on the revs, the cooler simply can't flow enough air.

Correct me if I'm wrong, but I think this setup should really start singing at around 4000/4500 rpm, right where its all over....

I'm condisering sending the cooler to Garrett for a recore (Nizpro tanks are good as far as I know?) and getting the turbo high-flowed/steel wheels. Any other recommendations? Will I need a fuel cut defender (sometimes it surges/cuts under boost at lower revs - i.e. full boost to manifold) or rising-rate reg?

Thanks for any input,

Roo

post-43945-1196474552_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3507884
Share on other sites

None taken :P .The reason for such odd Power vs. Torque figures is due to a rather restrictive intercooler. Between about 2100-3300 rpm I have access to full boost (10p.s.i), but by the time I've reached 4500 rpm its all the way back at 6 p.s.i :( You can see on the dyno sheet where the boost really falls off. Once its gets up on the revs, the cooler simply can't flow enough air.

Correct me if I'm wrong, but I think this setup should really start singing at around 4000/4500 rpm, right where its all over....

I'm condisering sending the cooler to Garrett for a recore (Nizpro tanks are good as far as I know?) and getting the turbo high-flowed/steel wheels. Any other recommendations? Will I need a fuel cut defender (sometimes it surges/cuts under boost at lower revs - i.e. full boost to manifold) or rising-rate reg?

Thanks for any input,

Roo

If I may voice my opinion... :)

Well if you want to get the most from your engine set up (RB25 / 30DET) then I would suggest a fairly large low mount turbo such as a Garret GT30 / 82R, dont bother high flowing the one you have.

Im using a GT30 / 71R (slightly smaller than the 82R) and it is good for about 250rwkw, the larger GT30 / 82R will be better for your engine because you have more down low power because of the larger capacity and it will probably spool a larger turbo pretty quick.

If youre going for out right power then you will need a fuel pump - go for a Walbro in tank or Bosch 040. You'll also need to upsize your injectors as the standard ones will max out pretty quick, go for some SARD 550cc brand new squirters, dont bother having the standard ones high flowed.

As for your intercooler, I have been using a Just Jap / Cooling pro 300 x 600 x 76 front mount for a while and Ive never had a problem, I would highly recommend one for the price.

Get in contact with GCG in Sydney for the turbo, Powerflow injection for the pump and injectors and Just Jap for an intercooler.

Im using similar equipment in my RB25DET (550cc injectors, 040 pump, GT30 / 71R and JJR front mount) and my car makes 230rwkw and 550nm at 18psi, very conservative AFR and it has bugger all lag.

:D

post-17958-1196919715_thumb.jpg

Edited by Bullet32
Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3517303
Share on other sites

Great, thanks for the info :P

For the moment its on hold due to a matter of funds, but I will definitely take your advice into consideration. I have been considering dropping the whole lot into an R32, but again this is more likely to happen later rather than sooner, once I finish my apprenticeship :P

BTW, anyone know what a good R32 rolling shell might be worth, just out of curiosity?

Cheers, Roo

Link to comment
https://www.sau.com.au/forums/topic/191734-new-act-member/#findComment-3524527
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...