Jump to content
SAU Community

Recommended Posts

hi,I have just got myself a r32gts4 man.std but for 3inch ex,hks bov,k&n panel filter.want to upgrade,but have some questions,where to start?,i have Haltec interceptor,will this do the job? im guessing i/c,dump,ecu,injectors would be some of the first things to look at,so was hopeing for advice on where to start..stdRB20 5spd.cheers.$2000 to spend for now..

Edited by Jamie72
Link to comment
https://www.sau.com.au/forums/topic/192146-mods-for-r32gts4/
Share on other sites

Get yourself a front mount kit from just jap they seem to work fine, a good dump pipe if you dont allready have one, chuck the rubbish k&n filter in the bin keep the airbox just put in a BMC or APEXI panel filter a good boost controller preferably Electronic and closed loop (AVCR or HKS EVC) sell the interceptor and get full management of some form (cough power fc cough) the ecu is the key to so many doors, if i had my time again i would buy that first before anything else if your a newbie spend some time and research before you buy you will also learn heaps along the way.:) hope im a help of some form

Get yourself a front mount kit from just jap they seem to work fine, a good dump pipe if you dont allready have one, chuck the rubbish k&n filter in the bin keep the airbox just put in a BMC or APEXI panel filter a good boost controller preferably Electronic and closed loop (AVCR or HKS EVC) sell the interceptor and get full management of some form (cough power fc cough) the ecu is the key to so many doors, if i had my time again i would buy that first before anything else if your a newbie spend some time and research before you buy you will also learn heaps along the way. >_< hope im a help of some form

thanks ,that should point me in the right direction,got a blitz dual sbc,should be ok?

You can end up spending alot more than you would buying a real GTR as something worth keeping in mind.

If you want something fairly mild then;

* Exhaust is a good place to start (turbo back).

* Aftermarket ecu, sort timing and fuel out prefferably or S-AFC.

* Clutch and Flywheel upgrade will be needed once power is up , a lightweight flywheel while your at it.

* You will need fuel pump and injectors once you step into an upgraded turbo

Lots of things you can do really but, depends on what you would like the car to be.

If you want lots of power in the long term, just save for a built RB26 it more or less drops straight in with very few bits to get. The GTS4 gearbox is the same strength wise too, it's not the poxy RB20 box out of gtst's.

For the record the K&N panel filters are fine and re-usable, sorry 13thracer I've used exactly the same panel filter on a high powered GTR (among other cars) with more power than the lowly RB20 is ever going to produce. People only have issues with them when they don't read instructions and over oil them.

Have a good read of some of the links here:

http://www.skylinesaustralia.com/forums/t66556.html

Specifically this one:

http://www.skylinesaustralia.com/forums/t45218.html

Goes over the basic items for you.

Cheers

You can end up spending alot more than you would buying a real GTR as something worth keeping in mind.

If you want something fairly mild then;

* Exhaust is a good place to start (turbo back).

* Aftermarket ecu, sort timing and fuel out prefferably or S-AFC.

* Clutch and Flywheel upgrade will be needed once power is up , a lightweight flywheel while your at it.

* You will need fuel pump and injectors once you step into an upgraded turbo

Lots of things you can do really but, depends on what you would like the car to be.

If you want lots of power in the long term, just save for a built RB26 it more or less drops straight in with very few bits to get. The GTS4 gearbox is the same strength wise too, it's not the poxy RB20 box out of gtst's.

For the record the K&N panel filters are fine and re-usable, sorry 13thracer I've used exactly the same panel filter on a high powered GTR (among other cars) with more power than the lowly RB20 is ever going to produce. People only have issues with them when they don't read instructions and over oil them.

thanks for the great info.happy about the gearbox,definate bonus.and that i didnt waste my 90 bucks on the k&n :rofl: i`m thinking the power fc seems like the way to go.exhaust is 3inch from turbo back,has hks voltage stabiliser,...ps.will the apexi pfc work with my blitz dual solinoid b/c ?

as you may or may not know the gts4 is a bit heavy..i think as heavy as a gtr but it has the power of a gtst. Therefore making it a bit lighter would help to

here is a thread about making a r32 gts4 lighter i started a while ago

R32 GTS4 Lighter

hope it helps :P

weight reduction is good :D:):D:) dont quote me but from memory the oldschool drag racers used to say loosing 400 pounds is equal to adding 100 HP and the best thing about weight reduction less impact on your driveline and most of it is free.

Edited by 13thracer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...