Jump to content
SAU Community

Recommended Posts

hi guys, im from the states and i need of a bit of help with my r33. ive checked the turbo, its good in working order, i just changed plugs and checked gaps for each. the car runs super rich about 9-10 a/f at low throttle just cruising, however at WOT the car leans out as it builds boost and jerks violently. also if i hold the throttle about half way it will build about 3 or 4 pounds and feels as if im brake boosting, suction from the intake/turbo is loud but no acceleration without the jerking. but as soon as i punch it it knocks and flips out. i changed plugs again and no help also checked vacuum sources and double tripple checked everything. im at a loss. there are no check engine lights. 127km on the car and motor. also car reacts the same way with the boost controller on or off.

mods include:

pod filter

front mount

turbo back exhaust

greddy profec boost controller at .6 bar

afc neo with decel at 1% throttle, 1.2 at 1000 and 3.8 at 2000. no tune.

thank you all for your help.

Edited by Jbunn2001
Link to comment
https://www.sau.com.au/forums/topic/192259-rb25det-acting-strange-help/
Share on other sites

ive only experianced this once. and im sure you've probably checked i i found i tiny hole in the intake pipe just after the cooler... was fine cruising... hit the throttle and yeah feels like break boost then WACK and big jerk of the car.

replaced the silicone hose no problem from there on.

ill try that again, maybe i over looked something. also for an update i just drove the car after i did nothing...... lol and it hiccupped a few times and was maintaining boost, but i ran ass rich this time all the way through only hit 12.2 after the hiccup then back down to 9.9- 10.3. so im thinking of a few things i need to address.

Coils.... ive already ghetto taped mine hoping they wouldnt arch

AFM- but i would assume i would have a check engine light

or... i stilll dunno.

i will check the intercooler piping and change the silicone cupplers and get some propper t-bolts.

thanks again

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...