Jump to content
SAU Community

Recommended Posts

Hey all just popping in real quickly again to ask the opinions of the forum. Car is a 95 gts-t with fmic, pod with cai, 3.5" turbo back exhaust split dump, running 12 psi with an ebc, always run 100 ron fuel, plugs gapped at .6 or .7, stock everything else and afc neo. Now I was watching my afr's the other day at full throttle and without a tune on stock ecu the reading I got was never below 11 is that common for a skyline with these few mods? Now I'm thinking the readings are definately off cause while at idle I never get anything below 16 just want to confirm that the wideband is stuffed, when at full throttle I never get anything below 11 and I had the wideband exposed to exhaust fumes and heat for like a week before I got power to it. All help is appreciated and welcomed. Thanks again in advance. Also a friend of mine has a ca18 that he wanted to get 300 - 350 rear wheel hp out of and I was wondering if you guys could help out or point in the right direction car is virtually stock and its an automatic.

Link to comment
https://www.sau.com.au/forums/topic/192302-is-this-heard-of/
Share on other sites

it cant hurt to get your readings checked against a calibrated 5 gas analyser.

Also those WB02 sensors are very sensitive to exhaust leaks.

Unless your exhaust sytem is 100% sealed then your readings are worthless

I think all skylines with stock ecu's do it once you add boost, thats why so many people get s-afc's to get that extra power, mine runs down to 10.5ish on full throttle!! although I haven't run it again after putting in a new 02 sensor. but I wouldn't stress about it mate >_<

Silly question here.. is the AFC actually tuned?

A tune of the AFC would resolve this... being thats what they are used for

Nismoid thats why I am asking the question, not silly at all ,I'm thinking its a bit high for an untuned skyline on stock ecu.With the mods I listed thats a whole lot more breathing room for the engine so I was expecting 10's at least, another mod I forgot to mention is a bosch 040 fuel pump recently installed like 3 months back, also fpr with gauge and stock pressure reads 44 psi at idle without vacuum. At idle also the widebands reads and shows nothing less than 16 and goes all the way to lean as the car warms and in closed loop mode still nothing less than 16 just was wondering if this is common or can I say the wideband is stuffed come on you don't find this a bit strange. Now i can't say my exhaust is perfect but there are no leaks I can visible hear or see.

I think a few people have missed the point. The 02 sensor should be keeping the AFR at ~14.7 in closed loop as Fat is saying. Usually it would be a bit richer at full throttle also.

Most likely either:

1. Stuffed measurement device (AFRs its reading are wrong)

2. Stuffed fuel pump

3. Stuffed Fuel pressure regulator (check fuel pressure at rail at idle)

4. Stuffed O2 sensor (Doesn't explain only 11:1 AFR at full throttle - usually would be richer)

4. Stuffed AFM (less likely)

Edited by benl1981

if you want good ratios, you need a tune.

02 sensor has little to do with it most of the time. thats why some people run it without that feedback. also the ratios depicted may be inacurate depending on where the wideband is installed in the exhaust and the piping size. any leaks (which many cars have) makes it even more "guessy"

11s is not that rich anyway

That's what he's saying - he expected it to be running richer than that. Mine was in the 9-10s when I upped the boost which is usually how they go.

O2 sensor is what sets the AFRs at light load and idle. In fact I can drive around town in closed loop most of the time if I baby it round. The tune has to be close to the mark first but then the 02 sensor will bring it back to 14.7 AFR by playing with the injector duty cycle.

Take it to a dyno and pay $50 to get it checked there both on idle and full throttle, then if its the measurement device you havent wasted your time trying to fix a problem that isnt there.

Edited by benl1981
I think a few people have missed the point. The 02 sensor should be keeping the AFR at ~14.7 in closed loop as Fat is saying. Usually it would be a bit richer at full throttle also.

Most likely either:

1. Stuffed measurement device (AFRs its reading are wrong): Really think so either the wideband O2 is stuffed or there is a leak in the exhaust cause I did all the test on the device to troubleshoot it and everything was spot on

2. Stuffed fuel pump: Brand new bosch 040

3. Stuffed Fuel pressure regulator (check fuel pressure at rail at idle):44psi

4. Stuffed O2 sensor (Doesn't explain only 11:1 AFR at full throttle - usually would be richer): Maybe read that if you have them connected without power to it might stuff it up and i did for like a week thats the wideband tho have a narrowband on the way that I will install ths week

4. Stuffed AFM (less likely): Could be but doubt it

That's what he's saying - he expected it to be running richer than that. Mine was in the 9-10s when I upped the boost which is usually how they go.

O2 sensor is what sets the AFRs at light load and idle. In fact I can drive around town in closed loop most of the time if I baby it round. The tune has to be close to the mark first but then the 02 sensor will bring it back to 14.7 AFR by playing with the injector duty cycle.

Take it to a dyno and pay $50 to get it checked there both on idle and full throttle, then if its the measurement device you havent wasted your time trying to fix a problem that isnt there.

:Wish I could but dynos are rare over here would fix a whole lot of shit but have to wait a month before they bring the dyno back!!! :rolleyes: You all know how it is once you get someting you want it perfect right away just don't have the tools man so I gatta eliminate stuff on my own really think its a leak tho with the seal around the gaskets of the decat pipe might be my mind but think I can hear a little air escaping will get that siliconed also the dump pipe area and move the wideband O2 sensor to just before the deact pipe tis weekend and see if that fixes it.
it cant hurt to get your readings checked against a calibrated 5 gas analyser.

Also those WB02 sensors are very sensitive to exhaust leaks.

Unless your exhaust sytem is 100% sealed then your readings are worthless

Hey Thanks all found the prob as you stated they are very sensitive to exhaust leaks. There is a hole the size of my finger right above the wideband O2 sensor bung half assed welder didn't weld it properly. Gonna get it welded shut on the weekend hopefully this person does a better job and I can finally tune the car properly.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...