Jump to content
SAU Community

Lack Of Rca Connections

GTAAAH

By GTAAAH,
in Car Audio & Electrical

 Share

Recommended Posts

GTAAAH Mentor

GTAAAH

Posted
Posted

I can't afford to replace my head unit at the moment but want to install another amp

Currently it has 1 amp which uses 4 RCA connections (2 front 2 rear) and the head unit has 4 RCA out's

I want to install a mono block with 2 RCA outs (i am pretty sure i only need connect 2 of them) but am unsure how to get these RCA's

Any suggestions, the head unit only has 4 RCA outs

Link to comment
https://www.sau.com.au/forums/topic/194089-lack-of-rca-connections/
Share on other sites
R33TOM Community Regular

R33TOM

Posted
Posted (edited)
ah ok cheers! wasn't sure whether these would drop quality, almost bought a new head-unit today, luckky

Also should i split off the L and R rear channels or the L and R front channels? I'm thinking rear

there will be a slight drop in signal level but would not affect the quality, well not that your be able to tell by human ears.

shouldnt matter if its the front or rear channels if your using it on a mono block amp purely for bass,

Edited by R33TOM

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...