Jump to content
SAU Community

Clutch Friction Point

moobaque
 Share

Recommended Posts

moobaque Rising Star

moobaque

Posted
Posted

Hey All,

Ive been doing some searching through the forums about adjusting the clutch friction point on a R33 Gtst and it seems that the only adjustment available is at the back of the clutch pedal.

Currently my clutch takes up with the pedal almost fully out. if i just have my foot resting on the clutch it can be enough to allow it to slip.

My problem is i dont see how adjusting the back of the pedal is going to be benificial in the sense that i just want the friction point to be further down the pedal stroke. But if i spin that U bracket up or down the thread, in my mind thats simply going to move the pedals resting position further or closer away from the firewall but the friction point on the pedal is still exactly the same. also keep in mind it doesnt appear that the piston going into the master cyclinder can come out and further if i was to spin the U bracket down the thread, but then expect to have the pedal return to the same position... if that makes any sense?

post-3061-1158191313.jpg <- clutch pedal attaches here

Please someone tell me i'm wrong coz i would really like to fix this... and im hoping my clutch just isnt to far warn....

Cheers

Camden

Link to comment
https://www.sau.com.au/forums/topic/195918-clutch-friction-point/
Share on other sites
chinkeboi Rising Star

chinkeboi

Posted
Posted

umm when my clutch cylinder leaked and had to get repaired.. it wasnt bled in properly. The clutch friction point was as what you describe. It was RIGHT at the top/end of the peddle.

I then took the car for a trash and noticed it was slipping like crazy from 4-6000 rpm.

Took car back to mech and he stuck his head under the dash where the pedals are and adjusted something.. the pedals friction point then sat at a lower position.

From what he told me... the clutch pedal should have some free play at the top of the pedal.. if it doesnt it could mean 1 of two things.. either

a. the clutch pedal needs to be adjusted

or

b. the clutch is on its way out

moobaque Rising Star

moobaque

Posted
  • Author
Posted

I dont think the clutch is dead coz its been like the for quite a while and hasnt been gettin worse. i do also have a little bit of freeplay at the top but as soon as u get past that freeplay ur at the friction point. Ive never noticed it slip under load on the track either (lots of 5000 to 7000rpm)

heh this only started anoying me after i drove my mates r33 and the friction point was way down the bottom...

I was also under the impression that my clutch was standard but after this same drive in my mates car my pedal is WAY heavier than his... I guess this could just mean i havea different clutch... or maybe worth a bleed?

moobaque Rising Star

moobaque

Posted
  • Author
Posted
i had the same case when my clutch wasn't bled properly. felt all funny n stuff. i bled it from both nipples properly and it's back to normal again.

mine has been this heavy from day 1 so its prolly just the way it is. but i think i will bleed it anyway coz i'll be pretty excited if it did become lighter.

gsf250 Apprentice

gsf250

Posted
Posted

my clutch was adjusted wrong by a mechanic and the friction point was moved to where yours is. Ive since fixed it and the friction point was returned to normal but the clutch is now dead.... 1 clutch kick too many oh well it lasted long enough for a stock clutch.

moobaque Rising Star

moobaque

Posted
  • Author
Posted

Ok new questions to do with this whole clutch issue

I had a go at trying to move that U bracket to see if it would make the difference in the clutch pedal but I hit a bit of a snag.

i pulled the split pin and took out the short pin that links the U bracket to the back of the clutch pedal.. and thats about as far as i got. How do you get the clutch pedal far enough away from the U bracket so that you can spin it up or down the thread? Im really not keen on forcing the piston to lean up or down to try and get it out from the pedal.

Im sure it must be really simple, just couldnt work it out.

Cheers

Camden

mattymagoo22 Community Regular

mattymagoo22

Posted
Posted

Hey mate,

You don't need to remove the pin and springclip.

Just loosen the nut behind the U bracket and wind the pushrod counter-clockwise, after you've turned it say one rotation jump up into the seat start her up and see if the pedal is where you want it, adjust as necessary, once it is right lock the nut against the U bracket and you're set.

By winding the pushrod you are moving the postion of the U bracket. When the U bracket is moved the friction point changes in relation clutch pedal travel. If you look under the dash when you are adjusting the pedal you'll see the pad where the pedal rests. If the U bracket is too far out this will keep the pedal partially engaged, and the clutch will quickly wear out/slip. by moving it in you'll prevent this from happening because as the clutch wears the friction point will gradually get closer to the top.

After you've made the adjustment if the pedal doesn't feel right you may have air in the system and these systems are not fun to bleed.

moobaque Rising Star

moobaque

Posted
  • Author
Posted
Hey mate,

You don't need to remove the pin and springclip.

Just loosen the nut behind the U bracket and wind the pushrod counter-clockwise, after you've turned it say one rotation jump up into the seat start her up and see if the pedal is where you want it, adjust as necessary, once it is right lock the nut against the U bracket and you're set.

By winding the pushrod you are moving the postion of the U bracket. When the U bracket is moved the friction point changes in relation clutch pedal travel. If you look under the dash when you are adjusting the pedal you'll see the pad where the pedal rests. If the U bracket is too far out this will keep the pedal partially engaged, and the clutch will quickly wear out/slip. by moving it in you'll prevent this from happening because as the clutch wears the friction point will gradually get closer to the top.

After you've made the adjustment if the pedal doesn't feel right you may have air in the system and these systems are not fun to bleed.

Awesome, so your saying there is no issue with the rod being spun inside the master cylinder. that i wasnt sure about. i'll give this a burl when i get a chance.

Cheers mate

Camden

  • 1 year later...
  • 1 year later...
Harey Veteran

Harey

Posted
Posted
what are you guys using to wind the pushrod? There is a bit of grip on there so I've been slowly adjusting with pliers but theres gotta be a better tool for the job

I just used some pliers as well. Bit slow but got there.

You guys are all weak, its not that hard to get down there... :ninja:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Duncan
      What brakes on R34 GTT(Europe)

      By Duncan · Posted

      Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...