Jump to content
SAU Community

Recommended Posts

Hi, was after a few ideas of things to check with my r33, the problem is soon as it starts boosting up it missfires to the point it just doesn't run, just coughs and splutters, this happens at about 4 psi, as soon as i back off runs perfect. Things i have tried to do to rectify the fault is change, ecu, spark plugs (all came out totally black), afm, cas, ignition relays checked, igniter (the earth seems good too, I asume its the one that goes under one of the coil holding frame bolts), JJR coils went in about a week before this happened aswell. I haven't yet pressurised the system to check for air leaks yet but all the cooler pipes seem well sealed.

cheers

Edited by SevenAngryPenguins
Link to comment
https://www.sau.com.au/forums/topic/197788-bad-missfire-under-boost-not-coils/
Share on other sites

im having same problem aye, did urs start doing it suddenly? me mate put 95octane in his skyline and the thing just startn to get worse and worse missing, we changed the plugs and fuel filter but thinking mayb the injectors are screwed

dont know anyone else with a 33, but i chucked the old coils back in and the problem is still there

plugs are bcpr6es

Edited by SevenAngryPenguins

hook it into the fuel rail if its a standard pump at idle it should see around 40psi if this is the case then its alright but under load if it doesnt make anymore than that I would think your fuel pump would be dead.

i put in a walbro a few months back and when it primes it sounds strong but i will still check it, how did you look at the gauge under load, i will have to get my little brother to sit on the engine while i boost down the road.

Edited by SevenAngryPenguins

after lots of stuffing around ended up buying a supercheap aircompressor to check for boost leaks and found a massive one so problem solved!!

Edited by SevenAngryPenguins

it was where my first pipe off the intercooler joined with the crossover pipe just after it goes though the engine bay wall if that makes sense, it was joined with a silicone joiner it appeared as if it was perfectly sealed but the clamp was done up right on the edge of the metal pipe inside with a bit of air pressure it leaked like a siv. I'm a bit annoyed at myself that I didn't check the hoses more closely the first second and third time that i did it. Would of saved alot of stuffing around.

a picture speaks a thousand words so they say

post-36364-1198114946_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...