Jump to content
SAU Community

R33 Wipers

Krishy

By Krishy,
in South Australia

 Share

Recommended Posts

Krishy Grand Master

Krishy

Posted
Posted

hey guys i was wondering if this has happened to anyone before....

my r33 front wipers doesnt work anymore....it is weird as it has all of a sudden died on me....so if anyone can help me or point me in the right direction that would be great help...the rear wiper works just not the front one...

cheers

Krish

Link to comment
https://www.sau.com.au/forums/topic/198843-r33-wipers/
Share on other sites
Krishy Grand Master

Krishy

Posted
  • Author
Posted

cool cheers guys i am checking out all the fuses today expect the fuse box has everything written in japanese so cant make sense of anything...so i am going to pull all of then out one by one and check it that way....

Link to comment
https://www.sau.com.au/forums/topic/198843-r33-wipers/#findComment-3548920
Share on other sites
ukai Enthusiast

ukai

Posted
Posted
cool cheers guys i am checking out all the fuses today expect the fuse box has everything written in japanese so cant make sense of anything...so i am going to pull all of then out one by one and check it that way....

If you look in the forums (general maintenence) theres translated fuse diagrams somwhere :)

Link to comment
https://www.sau.com.au/forums/topic/198843-r33-wipers/#findComment-3550705
Share on other sites
Luciano Veteran

Luciano

Posted
Posted (edited)

Sorry to hijack your thread Krishy;

I was wondering if any chance those fuses in that table ^ would result to the lights behind my speedo/rpm/fuel/oil gauge cluster suddenly not working? (indicators and warning lights are all fine)

i did a few searches and noticed a lot of people who had this problem also had their tail lights not working, and replaced the tail light fuse in the boot next to the battery to fix the problem.

My tail lights are still working however, and the fuse in the boot is fine... :)

edit- may just be a case of having to taking the cluster out today and having a look at the globes. I thought it was a little odd, as i read that theres a couple of lights behind there (rather than just one) , and them all burnt out at the same time is a bit iffy.

Edited by MSPEC33
Link to comment
https://www.sau.com.au/forums/topic/198843-r33-wipers/#findComment-3550859
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...