Jump to content
SAU Community

Recommended Posts

Hi,

Just wondering if anyone knows of a place I can buy the HKS pod filter replacement?

I just need the foam/filter inside.

I know I can order these online or get them from ebay. But is there a place in Canberra that sells them?

Or some kind of equivalent I could use?

Thanks :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/199348-hks-pod-filter-replacements/
Share on other sites

Yeah it stuffed alright lol.

I've actually had problems with my AFM because of this.

When I took it out I noticed it is tearing on the outside. It must have been in there for a while :thumbsup:

I'll pick one up from Trojan tomorrow hopefully.

Thanks for the help

Hope I'm not too late;

You need to buy the dry triple layer element. The twin/dual layer units are an oil/foam setup and can contaminate your afm [which you can clean with carb cleaner etc]. The triple layer units are dry and you will not have this problem. Advan in Sydney have them - they are light blue units [dual layer are usually purple or green].

Hmm...I've already ordered some from Trojan. I don't know if they are dual or triple layers...

I need 150mm filters, they only had 200mm. Which were the green ones; I will assume this means I will get the same ones but in 150mm. Oh well; I'll have to ask them about the triple layer filters.

Thanks for the help :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Google says for a 1998 Nissan Maxima to pull/pry, and the metal pin might even come out with it. I'd do a bit more googling, there was a few videos, find some where the shafts/needles appear most similar and compare the techniques.
    • Details: Turbo Borg Warner EFR 9180 with 1.05 rear housing Upgraded TurboSmart integrated BOV Sanded and powdercoated compressor cover in gloss black Elbow welded with wiggins clamp Speed Sensor(Not included) (Can include oil drain(heat wrapped + titanium intake pipe with almost new filter for a tad extra). Manifold: 6 Boost RB26/30 twin scroll manifold  e-MAP ports drilled into both scrolls(I was using the TAARKS EMAP KIT) Turbo is in excellent condition. Always used Penrite 15w50 Racing oil(Changed less then 2000ks). Also using the Turbosmart OP regulator and filter. Downpipe: 4inch Stainless steel with VBand inlet and outlet clamps(included) Heat wrapped Dual ports for Dyno/Wideband usage Will throw in free 2.5 inch intercooler pipe(2.5inch From turbo outlet to 3.5 inch intercooler) - Powder coated black. Turbo made 563rwkw on mainline hub dyno at around 24-25psi boost - Pump fuel. Will def make over 600kw on e85. Didn't bother as my e-MAP was through the roof with my setup sitting past the choke line. I have a cnc ported and fully built head on my 3.2. Turbine speed saw max of around 109k rpm. I'm running this on my R32 GTR, with AC, and the original power steering pump. The manifold clears the AC lines, ABS, and everything else. Although I had new AC lines because I just wanted new ones and I heat wrapped them as well. This will make more power on a slightly lower capacity motor with a higher PR. And I have since upgraded to a G45-1500. Have pics and videos if need be.  Absolutely nothing wrong with setup. Turbo is in perfect condition. No shaft play or oil leaks at all. All the work was professionally done. The transient response of this is fkn amazing. I cannot rave more about this turbo. If I wasn't chasing 4 figures, I would have kept it. $5000 NZ. Located: Auckland, New Zealand.    
    • I particularly like the look of the John Player Special team. (Thumbnail isn't different but hit play for the clip)  
    • Such a cool collection of cars back then.  
    • Mystery solved, thanks bro Bit of a strange mix, but i dont mind it, still looks good. 
×
×
  • Create New...