Jump to content
SAU Community

Recommended Posts

Well after washing my car on the weekend and realising that the inside of my back tyres was errr slick i thought it was about time i got rid of my 225/50/16 Faulken ZE502's (done atleast 30,000km) and get some fresh rubber.

Reading over an article in a recent Wheels Magazine I had my eye on the Dunlop FM901's as many people had said they were a great all round tyre. The FM901 ended up only 5th out of 7 tyres but got good reviews, just scored low due to taking an extra 50cm to stop or an extra 0.2sec per/lap during the testing, none of which would matter or be noticable to me.

The salesperson at my local Bob Jane T-Marts (thanks Paul) recommended either the 225/50/16 Yokohama A539 ($197/ea) or the 225/50/16 Michelin Preceda ($235/ea) instead of the 225/50/16 Dunlop FM901 ($279ea). He said the Yoko and Miche would be the best street tyres i'd ever drive on. So after thinking about the scores in the Wheels Magazine article i thought what the heck i'll get a cheaper tyre ($235/ea vs $279/ea) which actually is better performing (smart decision aye!).

Fitting and balance etc took almost 1.5hrs and $1,012 later (Tyres, Nitrogen filled, balance, alignment) I was on my way home. Immediately (3km) I went to my little straight stretch of smooth tarmac (private road of course) and gave em a real test to see how well they gripped and if if if if they would get rid of my axle tramp (oh dear god i hate axle tramp like u wouldnt believe).

First up i dropped the clutch @ 1500rpm and my god it just squatted and took off I was shocked. I was waited for the dreaded shutter from the axle tramp hehe. I pulled up again and dropped the clutch @ 3,000rpm. Alittle wheel spin (about 2m actually) and then it boosted and took off again, damn was I impressed. These things were launching 10x better than my 30,000km cheapo Faulkens. For my final 'phase 1' test i thought i'd launch in a guaranteed way to get axle tramp (with my old tyres)... Take off like u would from a normal set of lights in traffic to about 20km/h and then stomp it and hold on while the rear end shudders from axle tramp. I did this and whammo it just launched hard again, I thought "wtf ima try that again". So I tried it again and booya it launched again (about this time i nearly wet my pants realising that my axle tramp issues seemed to be gone).

Phase 2 will be to try the launches again all @ 12psi (instead of 7psi) and Phase 3 will be Eastern Creek Dragway.

Overall I'd rate these tyres a 9.8/10. They'd be a 10/10 if i had some wet roads to test them on but im sure with Sydney's weather that wet road is problably no more than about 3 days away.

img_tyre_pilotPreceda.jpg

Link to comment
https://www.sau.com.au/forums/topic/20048-michelin-preceda-tyres-small-review/
Share on other sites

Originally posted by benm

wet roads to test them on but im sure with Sydney's weather that wet road is problably no more than about 3 days away.

Spoke too soon... 12hrs later and its raining, although not enuff to really test the tyres out. In the wet they are quite good actually unless you try to drop the clutch where you can expect wheelspin. Corners and roads that i used to get easy wheelspin (in 1st 2nd and 3rd) i now have to -really- push it to try and get some wheelspin so im very pleased.

With some constant rain (instead of just enuff to have ur wipers on the lowest setting) im sure these tyres would start some magic.

Wet weather i'd rate these tyres about 8/10.

hi, nice review, did the sales guy say that the yokos were on par with the mich's? as im a bit of a fan of yokos, and wouldnt mind giving them a try.

where do the mich preceda's sit in the michelin range? ive driven on Mich Pilot SX's (i think now replaced by pilot sport?) and the grip is bloody incredible in the dry, and even in the wet! But to look at the tread pattern it doesnt look that aggressive which goes to show that the tread appearance really means stuff all when relating to the tyres performance.

eg check out the fully aggressive pattern of the falken 451's, yet ive been told these still spin up with not too much effort.

Originally posted by Turbo Tits

hi, nice review, did the sales guy say that the yokos were on par with the mich's? as im a bit of a fan of yokos, and wouldnt mind giving them a try.

I walked in and basically said "I want a -good- set of tyres for my skyline". Straight away he pointed at the Yokohama A539's in a 'clearance catalogue' and i immediately thought "argh just another salesperson trying to sell me what they have not what i want or need".

I then gave him my little spool about reading up on the FM901's in the wheels magazine test done earlier in the year (which i then realised the A539's he was pointing at actually came 4th in the wheels mag test and the FM901's came 5th). He then said that the Michelin Preceda's or the Yoko A539's would be the best set of tyres i'd ever drive on.

After getting the run down on the pricing of the 3 tyres i ended up getting the best tyre for the middle price range ($235 as opposed to $279 or $197).

  • 2 weeks later...

Done around 600km on these tyres now and they are fantastic. I'd love to take them to 1 of the 3 trackdays coming up over the next 2wks but i dont want to kill them.

These would have to be worth atleast 6-8sec a lap (at Eastern Creek) compared to my 25,000km old Faulken ZE502's which are now sitting at a dump somewhere.

  • 5 months later...

Just had my free 5,000km Service (even though i've done 8,000km) at Bob Jane T-Marts (Rotation, Balance, Alignment). These tyres are as good today as they were on the first day I got them. No noticable wear and no squeeling.

  • 2 months later...
Just had my free 5,000km Service (even though i've done 8,000km) at Bob Jane T-Marts (Rotation, Balance, Alignment). These tyres are as good today as they were on the first day I got them. No noticable wear and no squeeling.

benm -

how stiff are the sidewalls? They sound like a really good tyre

do they flex around and squirm around coners? Or do you feel alot of bumps with them?

I want a 225/50/16 that has nice stiff sidewalls for good handelling

Whats the grip like now they have a bit of wear on them?

have you had them on the track? what about 1/4 mile

Whats steering response like, are they really responsive or do you need to constanlty adjust how much you need to turn them?

How much is left on them after 10,000km?

Sorry for all the questions, but I dont know anyone else who has them, and I would like to try a set - just want to be sure thats all!

I haven't had them on a circuit (don't want to ruin them so early in their life) but have had them on the local 1/4 Mile Strip (the old track). I got major axle tramp in 1st and 2nd gear (same as what I used to get on the road with my old Faulkens which these Michelin's fixed - on the public roads).

I'll be at the new 1/4 Mile Strip tomorrow arvo and hoping that it was just the old tracks surface that was causing the problems and not my tyres.

I'm not 100% sure on tread depth, i'd have to have a look, honestly to me they look brand new after abit of tyre black has been used :D

I haven't had them on a circuit (don't want to ruin them so early in their life) but have had them on the local 1/4 Mile Strip (the old track). I got major axle tramp in 1st and 2nd gear (same as what I used to get on the road with my old Faulkens which these Michelin's fixed - on the public roads).  

 

I'll be at the new 1/4 Mile Strip tomorrow arvo and hoping that it was just the old tracks surface that was causing the problems and not my tyres.  

 

I'm not 100% sure on tread depth, i'd have to have a look, honestly to me they look brand new after abit of tyre black has been used :D

Cool. I am going to do some asking around tomorrow, and see what prices they are over here. See how it goes

Regards, Chris

  • 2 weeks later...

Here is my 60ft times from last nite at WSID. These tyres have done 10,000km and I had them set at 38psi.

60ft: 2.168 (~3,000rpm)

60ft: 2.117 (~3,500rpm)

60ft: 2.098 (~4,000rpm)

60ft: 2.111 (~3,000rpm)

Not bad I guess for an average driver :(

Benm, how long have these tyres been on your car? How much tyre tread is left? Ultimatey are u very conservative in ur driving and have the occasional hard acceleration bursts? Just tyring to work out how long wearing these tyres are.

Cheers

The tyres have done 11,200km and have been on my car for exactly 8mths. They have had a 5,000km service and are due for the 10,000km service (obviously).

I am unsure how much tread is left (see the pics below). I don't have the correct tools to measure them accurately.

I drive a Skyline whats this conservative thing your talking about :) ... I don't rip burnouts but I give them a good run. I live in a housing estate that hasn't heard of straight roads or traffic lights, instead its -very- twisty roads and a lifetime supply of round-abouts :)

mich1.jpg

mich2.jpg

mich3.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...