Jump to content
SAU Community

Sway Bars R33 Gts-t

Smitizen
 Share

Recommended Posts

Trust33 Grand Master

Trust33

Posted
Posted

this one is i have taken from sydneykid in the coilovers thread. we got to talking swaybars.

Thanks for the advice Gary. Atm im on a full whiteline stabiliser bar kit with urethane bush set, camber front and rear and pineapples set to standard.

the front adj blades on the swaybar im pretty sure though i could only get set up at 2nd and 3rd hole. can the front swaybars be adjusted any further? how can i do it? the rear is at full hard.

What size bars are you using? My guess is the off the shelf 24 mm front and 22 mm rear, which is too narrow an adjusment range for the track work you are doing, grip or drift. You should really be looking at 26 or 27 mm front and 24 or 26 mm rear. I don't recall what model it is, if it's an R32 then you need 4 adjustment settings on the front and 3 on the rear, standard (off the shelf) is 3 front and 2 rear. If it's an R33/34 then you need 6 adjustment settings on the front and 3 on the rear, standard (off the shelf) is 5 front and 2 rear.

You should also be using spherical bearing links on the bars to give you the instantaneous effect, plus increase the feel as you need as little dampening of the response for track work. They will need regular replacement, even the Whiteline greasable and dust covered ones. Just like brake pads they will wear out, they are a consumable after all.

To give some adjustment for the usage patterns that you have, you can't run spring rates that high, anything much over 5 kg/mm front and 4 kg/mm rear will negate the effect of any adjustment (bars, shocks or geometry) that you do. Use the bars to control the roll, that's their job after all and then adjust the rear subframe geometry to suite the traction requirements. At the moment you have nothing to adjust that will help with your problems.

Cheers

Gary

Somethings to think about;

You would need to use twice the spring rate to achieve the same anti roll as a stabiliser bar. Why? Because the inside wheel goes down the same amount that the outside wheel goes up. So a stabiliser bar has twice the movement for the same amount of roll as a spring, hence twice the amount of resistence to roll. Only the outside spring resists the roll, the inside spring does nothing.

When you are not going around a corner, the stabiliser bar does nothing, so you get more traction from the softer spring rate.

Stabiliser bars are easily adjustable, spring rates are not. If, on any given day, you need more or less front or rear anti roll you can't easily, quickly or cheaply adjust it with springs. That's why (when the regs allow) race cars have driver adjustable stabiliser bars.

Diagonal weight transfer is best resisted with anti roll, not spring rate. Under corner exit acceleration the outside rear tyres take a large amount of weight transfer, this manifests itself as lift to the inside front tyre. Reducing inside front tyre grip means that the outsdie front tyre is carrying more of the cornering load than would eb the case if the diagonal weight transfer was a resisted by a stabiliser bar. Excessive outside tyre wear and inability to maintain consistent lap speed due to overheating are all systems.

Too little anti roll has side effects. One of which is the need to run excessive amounts of camber, front and/or rear. This reduces the contact patch of the tyre for straight line acceleration and braking.

Running an excessively high spring rate becuase of a lack of antir roll has a few more side effects. One of which is the need to run excessively high rebound damping in the shock absorber to control that higher spring rate. This means the shocks resists (slows down) the downwards movement of the suspension and makes it more difficult to keep the tyre in contact with the road surface. Skipping from small bump to small bump is not good for traction.

I have several more pages in me if necessary, if anyone remains unconvinced.

Cheers

Gary

SKYPER Enthusiast

SKYPER

Posted
Posted (edited)

Selby's swaybars (not sure if they make swaybars for Skylines) -

http://www.hotfrog.com.au/Companies/Selbys-Swaybars

K-MAC swaybars (As far as I know the prices on the website are in US dollars

and they make swaybars for R32, R33, R34 in non adjustable and adjustable).

K-MAC website -

http://www.k-mac.com.au/

Swaybar prices -

http://www.k-mac.com.au/pages/tuning/listofkits.htm

Also I noticed they can custom make springs.

Edited by SKYPER
Smitizen Community Regular

Smitizen

Posted
  • Author
Posted
Selby's swaybars (not sure if they make swaybars for Skylines) -

http://www.hotfrog.com.au/Companies/Selbys-Swaybars

K-MAC swaybars (As far as I know the prices on the website are in US dollars

and they make swaybars for R32, R33, R34 in non adjustable and adjustable).

K-MAC website -

http://www.k-mac.com.au/

Swaybar prices -

http://www.k-mac.com.au/pages/tuning/listofkits.htm

Also I noticed they can custom make springs.

I thought Selbys was Whiteline?

Anyway thanks for the info and links .

Smitizen Community Regular

Smitizen

Posted
  • Author
Posted

they are hollow bars.

size f: 24.2mm

size r: 27.3mm

i use the gtr spec ones but they bolt onto my gts fine

gts spec ones are

f: 27.2mm

r: 23.0mm

Where did you snap these up from and how much did they set you back???

Sydneykid Grand Master

Sydneykid

Posted
Posted

they are hollow bars.

size f: 24.2mm

size r: 27.3mm

i use the gtr spec ones but they bolt onto my gts fine

gts spec ones are

f: 27.2mm

r: 23.0mm

Front GTR (4wd) bar won't fit a GTST (2wd), plus it is too soft a rate.

Cheers

Gary

Sydneykid Grand Master

Sydneykid

Posted
Posted
Gary,

I have forgotten....what are the size of the sway bars in the GB that I have? :P

From memory, 24 mm solid front adjustable and 22 mm solid rear adjustable.

Minimum adjustment is equivalent to a 27 mm hollow bar, with 6 steps of around 8% increase each on the front.

The rear is equivalent to a 24 mm hollow bar, with 3 steps of around 12% increase each on the front.

All the Jap hollow bars I have tried are grossly underdone. As an example, we swapped John's 300ZX hollow bars for some solid bars, backed off the spring rates a bit and it was 1.5 seconds a lap faster at Philip Island.

Cheers

Gary

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      M35 Aftermarket Fuel Pump

      By MBS206 · Posted

      Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Ben_D
      Wanted to buy R200 longnose LSD 3.9 ratio

      By Ben_D · Posted

      Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Ben_D
      Back for more after 18 years - and where are the longnose R200 LSDs?

      By Ben_D · Posted

      Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • sonicii
      G35 Control arm and Compression Rods into a V35 Skyline.

      By sonicii · Posted

      Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...