Jump to content
SAU Community

Apexi Power Fc Query

skylinekid

By skylinekid,
in Engines & Forced Induction

 Share

Recommended Posts

skylinekid Proficient

skylinekid

Posted
Posted

hey everyone im currently building my engine and want to go d-jetro with the apexi but i own an rb25det and they dont make the d-jetro unit to suite. but i have heard on the grape vine that u can make a bcnr33 d-jetro computer fit the rb25det is this true any help would be gr8ly appreciated

Link to comment
https://www.sau.com.au/forums/topic/200896-apexi-power-fc-query/
Share on other sites
dmac_25 Grand Master

dmac_25

Posted
Posted
hey everyone im currently building my engine and want to go d-jetro with the apexi but i own an rb25det and they dont make the d-jetro unit to suite. but i have heard on the grape vine that u can make a bcnr33 d-jetro computer fit the rb25det is this true any help would be gr8ly appreciated

It is possible that i know of with the standard pfc on the rb25det with no vct im sure the d-jetro pfc should work check out the thread about the power fc into the gts series if you were in melb there is a workshop that does the install

  • 2 years later...
seonho Apprentice

seonho

Posted
Posted

HEY i have same question. i wanna install a D-jetro on my r33gtst@ rb25det. (740 inj, gt30, poncams, cp pistons,N1 Oil & waterpump, gtr crank, walbro FP, Z32 MAF, nismo FMIC, Mocal 20R oilcooler.....)

I wanna change the maf to map 3,5 bar.

Do i have to change some wiring? do anyone have exp. with that?

big thx

Marcus

paulr33 Grand Master

paulr33

Posted
Posted

as mafia said search for the info, it's all out there

it's not a simple sensor change, you need to get BCNR33 PFC, then change the wiring, then change the tune, then you loose VCT

it's a lot of work just to run a map sensor. whatever you can achieve with the map sensor, you can do with AFM

and a 3.5bar map sensor is only 2.5 bar boost you know that dont you?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...