Jump to content
SAU Community

F/s: R33 Gtst 1993 2-door Auto

redevil

By redevil,
in Classifieds

 Share

Recommended Posts

redevil Proficient

redevil

Posted
Posted (edited)

Item: 1994 Nissan R33 skyline RB25Det

Location: Brisbane Southside

Item Condition: Good

Reason for Selling: Need a four door car

Price and Payment Conditions: $18,500 Neg or Swap for something of interest

Extra Info: Since June 2007 this car has had alot of work done to it both body wise and engine wise, I was building it up to compete in Autosalon series and doesn't need much more done to it. But due to work and family reasons i need a four door and have to get rid of my pride and joy. The car has 140,000km on it and on it's run in tune (I.E. turbo turned off end everything dialed back to allow engine to bed in) produced 324hp at the wheels, the car has alot more potential just with the motor only being 4000km old havn't had the chance to do a power run yet.

Engine:

Rb25det Tommy Karia edition Rebuilt by JHH

ACL race series pistons

Crower Rods

ACL race series bearings

RB26 Crank

Baffled sump

Ported and polished head

Modified oiling in the head to drain from the back

Tomei Valves and springs

Tomei Poncams

Custom adjustable cam gears

N1 oil and water pumps

Blue printed

Greddy Plenum

Trust TD06 turbo

S15 injectors 480cc

Trust 3" Exhaust with custom tips

Trust front mount intercooler

HKS mushroom filter

Body:

Do-Luck GTR front bar

D2 Front guards

Bomex side skirts

Veilside rear bar

M3 mirrors with working indicators

Rolled rear guards

Custom 2-tone paint job with cherry red pearl with zyrlex diamod pearl and Metallic black

Monkey Warehouse LED tail lights

Drivetrain and Wheels:

MV automatics Stage 2 Shift kit

Front mount Trans Coooler

Driveshafts balanced by Driveline services

Kaaz 2-way LSD

19" Axis Hiro's 8.5" Front and 10.5" Rears With Nankang tyres all around

KYB shocks front and rear

Steering rack replaced when doing rebuild

Interior:

Pioneer 6.5" In-Dash DVD player with VDP processor

Fusion 6.5" Front Splits

Fusion 6" Rear 2-ways

Fusion amp running front splits

Momo Millenium steering wheel

Impul Bucket seats (Genuine)

Turbo Smart E-Boost2

Blitz Boost gauge

Autometer Air Fuel guage

Apexi SAFC2

Full set of floor mats

As i said it's had alot of work done to it and really wanted to keep it, but due to unforseen circumstances have to sell.

Comes with RWC

Pictures:

Contact Details: PM me

post-9866-1200090113_thumb.jpg

post-9866-1200090142_thumb.jpg

post-9866-1200090158_thumb.jpg

post-9866-1200090165_thumb.jpg

post-9866-1200090173_thumb.jpg

post-9866-1200090182_thumb.jpg

post-9866-1200090198_thumb.jpg

post-9866-1200090203_thumb.jpg

Edited by redevil
Link to comment
https://www.sau.com.au/forums/topic/201186-fs-r33-gtst-1993-2-door-auto/
Share on other sites
  • 3 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...