Jump to content
SAU Community

Recommended Posts

Hey guys and girls

I just sold my rx7 because it was a petrol hungry beast, am now looking at a 34 non turbo

anyone know much bout them?

looks nice but is it good on fuel??? ive had enough with the petrol hungry cars looking for something more tame.

any suggestions or tips about the 34?

Link to comment
https://www.sau.com.au/forums/topic/203276-r34/
Share on other sites

Hey guys and girls

I just sold my rx7 because it was a petrol hungry beast, am now looking at a 34 non turbo

anyone know much bout them?

looks nice but is it good on fuel??? ive had enough with the petrol hungry cars looking for something more tame.

any suggestions or tips about the 34?

The Term "Petrol hungry cars" can be very wild, so in your standard how much Litre/100kms is too hungry for you mate thats the question.

So if you want a car that need next to nothing to run buy:

"Smart 4 Two" A.K.A Smart-car

Echo

Yaris

Getz

Swift

If you don't want a small or a compact car but yet uses less fuel then:

Camry

Aurion

VE commodore

Accord Euro

New lancer

If you want a car that have a sporting looks or go fast feel but yet retain some sort of fuel economy then:

Mini

FTO

Civic Type-R

Integra Type-R

350Z

Non turbo Version of R34,R33,R32, WRX Rs, Supra

Edited by MRR34
Link to comment
https://www.sau.com.au/forums/topic/203276-r34/#findComment-3605711
Share on other sites

if you can keep your foot out of it and drive sedately it will be MUCH better than a rotor.

I have a wagon that will chew 60lt of 98 octane petrol in 290k if I drive it wild. sedate it will do 550 on the same tank.

Link to comment
https://www.sau.com.au/forums/topic/203276-r34/#findComment-3606416
Share on other sites

a 34 NA is no more fuel guzzling than a 6 cyl commodore...and should definately be much better compared to a rotor.

althought my mrs gets 500-600 a full tank fuel using the cheaper ethnol blends.. FYI the NA auto RWD dynoed at 160hp @ rear wheel this is after a major service and tune as well

Link to comment
https://www.sau.com.au/forums/topic/203276-r34/#findComment-3611720
Share on other sites

They are decent for a six cylinder with mine getting about 10liters per 100kms on average, thats better than my 2006 hilux ute which is a 4cylinder. I wouldn't waste your time getting an na (thats wat i have) nice car and all drives great, but is pretty slow and also don't get an auto (extra slow). A manual might be alright, but power wise i raced my old r31 manual with just extractors and exaust against my stock auto 34 and there was nothing between them, over 120km the 34 would flog it. You would probly get a bit better fuel economy out of the manual version as well.

Edited by turtlepower
Link to comment
https://www.sau.com.au/forums/topic/203276-r34/#findComment-3623391
Share on other sites

  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...