Jump to content
SAU Community

Recommended Posts

Hey guys and girls

I just sold my rx7 because it was a petrol hungry beast, am now looking at a 34 non turbo

anyone know much bout them?

looks nice but is it good on fuel??? ive had enough with the petrol hungry cars looking for something more tame.

any suggestions or tips about the 34?

Link to comment
https://www.sau.com.au/forums/topic/203276-r34/
Share on other sites

Hey guys and girls

I just sold my rx7 because it was a petrol hungry beast, am now looking at a 34 non turbo

anyone know much bout them?

looks nice but is it good on fuel??? ive had enough with the petrol hungry cars looking for something more tame.

any suggestions or tips about the 34?

The Term "Petrol hungry cars" can be very wild, so in your standard how much Litre/100kms is too hungry for you mate thats the question.

So if you want a car that need next to nothing to run buy:

"Smart 4 Two" A.K.A Smart-car

Echo

Yaris

Getz

Swift

If you don't want a small or a compact car but yet uses less fuel then:

Camry

Aurion

VE commodore

Accord Euro

New lancer

If you want a car that have a sporting looks or go fast feel but yet retain some sort of fuel economy then:

Mini

FTO

Civic Type-R

Integra Type-R

350Z

Non turbo Version of R34,R33,R32, WRX Rs, Supra

Edited by MRR34
Link to comment
https://www.sau.com.au/forums/topic/203276-r34/#findComment-3605711
Share on other sites

if you can keep your foot out of it and drive sedately it will be MUCH better than a rotor.

I have a wagon that will chew 60lt of 98 octane petrol in 290k if I drive it wild. sedate it will do 550 on the same tank.

Link to comment
https://www.sau.com.au/forums/topic/203276-r34/#findComment-3606416
Share on other sites

a 34 NA is no more fuel guzzling than a 6 cyl commodore...and should definately be much better compared to a rotor.

althought my mrs gets 500-600 a full tank fuel using the cheaper ethnol blends.. FYI the NA auto RWD dynoed at 160hp @ rear wheel this is after a major service and tune as well

Link to comment
https://www.sau.com.au/forums/topic/203276-r34/#findComment-3611720
Share on other sites

They are decent for a six cylinder with mine getting about 10liters per 100kms on average, thats better than my 2006 hilux ute which is a 4cylinder. I wouldn't waste your time getting an na (thats wat i have) nice car and all drives great, but is pretty slow and also don't get an auto (extra slow). A manual might be alright, but power wise i raced my old r31 manual with just extractors and exaust against my stock auto 34 and there was nothing between them, over 120km the 34 would flog it. You would probly get a bit better fuel economy out of the manual version as well.

Edited by turtlepower
Link to comment
https://www.sau.com.au/forums/topic/203276-r34/#findComment-3623391
Share on other sites

  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...