Jump to content
SAU Community

Recommended Posts

budget for $800~1000 for a comprehensive tune ...

and $500~$700 for a get everything working ok tune ;)

remember tuning isn't just always about punching numbers into the ecu ...

the workshop that carries out the tune will most likely do a thorough check of the mechanical side of things to make sure your car can handle it and you may need a new set of plugs, full tank of gas etc etc.

also the better and reputable the tuner the more it'll cost generally.

best thing to do is talk to your tuner and see what they reckon.

Hope that helps :)

yeah thanks guys, this is helping heaps.

the only place iv found so far who will touch the emanage blue is allstar, and they want me to install and get the car running first.

i think ill be able to manage that

any other ideas on places tht might tune it ?

i only called xspeed and allstar so far. any other ideas ?

i got Top Racing to tune my car i got :

Power FC

Power FC boost controller kit

Z32 AFM

FMIC

Walbro Fuel Pump

3" cat back

3" dump pipe (stock cat)

and they charged me 300 then it was knocking like crazy cause they didn't do road tune but they were happy for me to come back after 2 days for the road tune got it done free of charge so yeah try them they're wicked ;)

yeah thanks guys, this is helping heaps.

the only place iv found so far who will touch the emanage blue is allstar, and they want me to install and get the car running first.

i think ill be able to manage that

any other ideas on places tht might tune it ?

i only called xspeed and allstar so far. any other ideas ?

can vouch for allstar, they do really good work.

  • 1 month later...
i have full race build rb30/26 + T78 3 hks fuel pumps + a whole Race fuel system

with pfc i was quoted $1000Canadian

I paid roughly $1100 for PowerFC tune + cam gears ($250) + tuning of EBC (minor). Expensive tune but great results, I did know another company that could do it cheaper but I decided pay the extra $$$ for the quality tuning :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...