Jump to content
SAU Community

Recommended Posts

Currently using MT ET radials - good for preliminary runs but will require slicks.

What i need to know is in the heat treatments GTR they are running the same wall and tyre diameter front and rear but the widths differ. The rears are substantially wider than the front.

They look like Dunlop may be Hoosier . Any one know what make and specs of tyre will allow me to do this and also what rims would be suited?

As i have mentioned i currently have standard GTR32 rims withy MT Et radials but need info to run slicks .

Also, if you are using an adjustable torque split controller (like the HKS or even hydraulic one) wouldn't that negate the need for same diameter tyres? Are you also allowing for tyre growth on the rears?

Also, if you are using an adjustable torque split controller (like the HKS or even hydraulic one) wouldn't that negate the need for same diameter tyres? Are you also allowing for tyre growth on the rears?

Nah - centrifugal force - both front and rear - i would say same tyre or similar growth , may be minimally larger at the rear when spinning but that doesnt count.

looking into the slick side of things - not that easy to find out info.

My rims are mint GTR and the MT are new and haven't been on car yet . I would like to work with you on this but i firstly have to find out the price and availability of the Bogarts and Goodyears - any idea where to buy these from?

www.bogartracingwheels.com :P

what about weld wheels?

MT ET drag wheels are about 5.5 kg each in 15 x 8", but the Bogarts are the lightest I know of (4kg each) and are about $400+ each wheel

Dave,

You can get weld racing rims from the states for just over $1000 delivered for 15x8's and are available in a heap of offsets. I reckon some M/T 15x26x8.5's would be a good starting point and are readily available especially toward the end of the season as they have sales.

I have a question about the legalities of running a slick on an awd car as I know last year it wasnt allowed under andra rules but they made exceptions for certain cars. Can anyone tell me if that has been changed in this years andra rule book?

Dave,

You can get weld racing rims from the states for just over $1000 delivered for 15x8's and are available in a heap of offsets. I reckon some M/T 15x26x8.5's would be a good starting point and are readily available especially toward the end of the season as they have sales.

I have a question about the legalities of running a slick on an awd car as I know last year it wasnt allowed under andra rules but they made exceptions for certain cars. Can anyone tell me if that has been changed in this years andra rule book?

Have just had a look at the Weld site Smiley - the $1000 delivered from the states is not so bad realy? we will have to have a good look at the offsets particularly on the front as i want to have her as low as possible but now with the ET's that i have -if i go any lower my uper arm will rub. Once she is back from the paint shop i will have to address this on a closer level.

May be i should just stick to what i have at this stage and in the interim check the ANDRA status?

I have a set of 5 stud 15x8 weld pro stars here with a 4.5" back space with some 15x26x8.5 M/T slicks you can try on to see whats going to fit.

That sounds good Smiley - didnt know you had those? Oh well that turned out well , catch up with you over the week end.

  • 3 months later...
The tyre and rim thing is resolved -thanks for all your input.

Fortunately scored - Advan rims and 10'" slicks - tyres not suitable for use but good for set up. A simple die grind over the calipers and on they went. These were off the Tomei Drag car that Hi octane had - i consider my self lucky and thanks to Mark Jacobson from Godzila racing.

Any one know where to attain extra long wheel studs and open light wieght nuts??post-10298-1212224284_thumb.jpgpost-10298-1212224052_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I should. But it already uses too much fuel for a daily. You might note my recco for engine chnages are almost exclusively to people who have it as a weekender/summer car. I don't even have room to keep the spares for this one, let alone another car.
    • If I had "perfect R33 GTR" kinda money I would have bought one of the crazy expensive low mileage HJA cars, but I am sadly not that wealthy. I already picked this car out of various Skylines for sale locally, most of which were worse in some way. Only a few cars were actually better but also more expensive. In terms of buying a motor locally, I at least have the option to inspect it myself and juding the seller as a person, and used or freshly rebuilt engines that some people sell are actually ok price-wise. I knew the car was going to require work, but shit piled up real fast and I haven't even driven 1000km yet as the turbo started oiling like a bitch within a few weeks after I got the car.   I assume it wasn't actually me who cracked it, though there is no way to know when that crack formed and if the previous owner even knew it was there. Buying another 05U Block can be a gamble, yeah, but the cheapest PRP cast block is like twice or more money-wise, and billet is 3 or 3 times as much. For now I am most likely just keeping the current engine, as a rebuild or engine swap isn't happening right now. But I am seriously considering buying a second engine and selling mine in return. Might be a sweet deal at the end.
    • Hi all. I need some help buying the correct size banjo bolts for my 2860 turbos. Because whoever installed them tore up the original part, I ordered new ones of this kind, because I just figured these were the most leak-resistant option as I already had trouble with a shitty braided line. I need to know the thread size of the smaller left hole, that is the turbo oil feed connection. I found out so far that the turbo oil inlet apparently has a 7/16"-24 thread, but I cannot find any listing or description of the thread size on this line. I do not have the original bolts. I tried using the bolts that were in the turbos (the ones that were mounted with the shitty braided line) but they sit very loosely so they can't be the right thread. Means either these bolts are the wrong ones (how do they fit the turbo then? no clue) or the wraparound-lines have a different thread than the turbo oil feed itself. Help is appreciated, asking Nissan directly is obviously not going to work.
    • EDIT: PSA to whoever stumbles upon this thread. It is in fact a crack in the block that caused this concern. Just letting you know. In my case, a few cm long hairline crack going horizontally above the turbo oil feed. Classic RB shit I guess
×
×
  • Create New...