Jump to content
SAU Community

Recommended Posts

After alot of debating between a C10, another DR30, R32 GT-R or something practicle I can use everyday.

I've made up my mind, it has to be the C10!

Does anyone know of any being complied in Australia and wether it was a pretty straight forward like any other import? or a complete and utter headf**k???

Also is much interchangable with more modern suspension/handling or will I be spending alot of time on a lathe/mill putting my toolmaking experiance into play customising parts to fit.

Basic compliance on the old girls, side intrusion bars rear retractables and rear parcel shelf anchors and a engineers sign off, if you're in Perth ring Tenagah Ant there is very experienced in compliancing and he has a ..... 78 SKyline, same will apply for a dr unlike a 32 gtr that will require raws spec full compliance and large bill

Thanks guys :thanks:

For the time being wont be off to perth anymore, I unexpectedly got offered a new job not too long ago here in Adelaide, and the money was way too good to refuse :PBJ:

also can someone give a me a good indication what I should actually be paying for a C10. I have seen some on some importer sites I wont name for $20-25,000+ (non complied)

But some sites i found awhile back (in japan) I could swear were around AU$10,000-$15,000. (would have to add shipping)

Cos my very good friend from Hong Kong frequents Japan and constantly is telling me how much cars actually cost in Japan and compliance + shipping costs + $1000 fee doesnt quite add up to what some of these importers are charging (FD RX-7 is a really great example), I just dont want the wool pulled over my eyes.

Can someone en-lighten me.

I wont be looking for something immaculate, just something that isnt a rust heap and complete.

Edited by benny_blanco

So what part of Adelaide are you going to

also SA has a VERY small car scene its bad, but mallala a drift track 50KM or so out of the city / my suburb holds drift days pfft once a month

soz to burst the bubble

Im allready in Adelaide :)

Was going to move to Perth until I got a very good job offer, which made me want to stay for another 12months.

In 12 months time who knows, the club scene in Adelaide is shithouse x100! And has made impossible to move any further DJ'n (as i refuse to play commercial garbage), apart from playing for the odd Internationals these days, here I am ''too underground'' for Adelaide!

The Adelaide hills are fun enough! why bother going to Mallala :D

Now back to the topic :/

Edited by benny_blanco
So what part of Adelaide are you going to

also SA has a VERY small car scene its bad, but mallala a drift track 50KM or so out of the city / my suburb holds drift days pfft once a month

soz to burst the bubble

Small car scene???? You obviously don't know the right people, people tend to keep on the down low these days.

You pay shipping, buyer's fee in Japan, plus import duty and GST on the FOB price.

You can definitely save money by buying and importing your own car, but if anything goes wrong, then you're in a whole lot of trouble (potentially). Many people look at the importer's fee as buying peace of mind. It cost me about $2k on top of what I could potentially have bought my R32 skyline for 7 years ago. Well worth the money in my opinion.

If you need to save every last $$ then have a go for yourself, but be aware that you may have a lot of leg work to do - very daunting for a first timer.

If you have to pay a reputable importer a couple of grand to get you the car you want, then I reckon it;s money well spent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Consider a 35 too...
    • He's right ~ there is no 'magic' with stuff like this ... it is more likely that in the process of looking for the short, the loom/wire 'incidentally' got moved in the process, thus removing the short ~ now, that maybe a wire (in a loom) rubbing against the edge of some grounded metal, that's worn through the insulation, causing the (now intermittent) short to ground. If one wire in a loom has been damaged in this fashion, it's reasonable to presume that other wires beside it may have also be damaged, and now exposed...you can bet the green crusty copper corrosion will start... ...that'd be a pisser, Murphy's Law steps right in as GTS observes...but worse, something like that is easier to find when shorted...ie; unplug bulb and fuse, and put multimeter in continuity mode so you get constant beep, and carefully poke about hoping to find if some movemet of the harness stop the beeping.... ...it's still all a bit Arnie tho' ..It'll be back... 😃
    • Yeah, but knowledge of one wire's insulation worn through to short on earth implies the possibility of other wires doing the same. I had my power steering die, because the wire that runs to the solenoid valve on the rack runs in the same loom as the power wire for the O2 sensor. And when the O2 sensor/wire did something stupid and burnt part of that loom to death, the only indication was the shit(ter) fuel economy and the heavy steering. It took deep excavation of the looms in the bay to find the problem. Not wear through in that case, but similar shit.
    • Ah, I thought he'd wired it to one of the spare ECU inputs! Too long ago since I read that post, ha ha. I've been arguing with radiators, harmonic balancers, alternators and rust since reading it.
    • Correct. The ECU cannot read oil temp. (Well, I think it probably can in some situations. I did have the thought of potentially repinning the ECU when I was doing oil pressure). I am using this into the MPVI dongle, so that the MPVI dongle can read oil temperature. It is attached to a VDO gauge which is obviously calibrated to whatever curve the sender actually is using. This would be easy if I could setup a table of voltage to temperature like many sensors, but it appears I cannot do this and can only setup the transform rule which appears to be Input (voltage) x Multiplier, and add an offset. This to me means it MUST be linear. So it may be a complete waste of time wiring this into the ECU. The idea was that the MPVI3 has standalone logging. I wanted to use this instead of a laptop with serial cable (for wideband) for long datalogs. Given the wideband also has electric interference, I may never trust this either in a world where the serial wideband and the analog output wideband do not agree. Last time I did a trace I could see the two wideband traces follow each other, but one was a little leaner than the other. I plan on playing with voltage offsets and actually driving the thing to see how close they correlate. If they never correlate... then, well, maybe I'll never use either. Ideally I'd like to have the Analog wideband read ever so slightly leaner than the serial one, because the serial one is 'correct'. Tuning the car to be ever so slightly too-rich would be the aim. Not needing to have a laptop flying around in the footwell connected with cables is... an advantage. About the only one from the forced upgrade to MPVI3.
×
×
  • Create New...